User manual FOSTEX VF160EX

[. . . ] 8588 044 000 (396678) Digital Multitracker INPUT 1/9/A 2/10/B 3/11/C 4/12/D 5/13/E 6/14/F BAL 7/15/G UNBAL INSERT BAL 8/16/H UNBAL MON OUT INSERT L R PHONES TRIM MON OUT PHONES LINE MIC PEAK LINE MIC PEAK LINE MIC PEAK LINE MIC PEAK LINE MIC PEAK LINE MIC PEAK LINE MIC PEAK LINE MIC PEAK 0 10 0 10 1/9/A 2/10/B 3/11/C 4/12/D 5/13/E 6/14/F 7/15/G 8/16/H CH STATUS/CH SEL CH STATUS ORANGE INPUT RED REC GREEN PLAY OFF MUTE RECALL SCENE STORE CLEAR OPTICAL DIRECT RCL MAP EFF EDIT EFF1 EFF2 ACCESS ACCESS +6 +6 MUTE 0 0 MUTE PHANTOM PHANTOM EQ/COMP HI-G/F/Q EFF1/EFF2 PRE/POST -10 -10 COMP INPUT SEL AUX1/AUX2 MID-G/F/Q REC ASSIGN BUSS REC TRK SOURCE DIRECT REC TRK INT MIXDOWN DISP SEL PGM SEL SETUP -20 -30 -40 -50 -60 -20 -30 -40 -50 -60 PRE/POST START PAN LO-G 1 FADER CH VIEW HOLD/ 2 AUTO RTN AUTO PUNCH IN OUT TIME BASE END IN CLIPBOARD ALIGN SEL OUT A RTN A PLAY - - 3 4 MARK UNDO /REDO 5 6 VARI PITCH 7 SCENE SEQ. CH PARAM EDIT STORE EDIT LOCATE SCRUB 1 CH STATUS/CH SEL 2 3 CH STATUS ORANGE 4 INPUT 5 RED REC 6 GREEN PLAY 7 OFF 8 MUTE TRACK P. EDIT EVT MEM CD PLAY RECORD STOP PLAY REWIND F FWD AUTO PUNCH +6 +6 +6 CLIPBOARD PLAY LOCATE ABS 0 LOCATE REC END PREV NEXT 0 0 0 FADER ADJUST -10 -10 -10 EXIT/NO LEVEL ADJUST -20 -30 -40 -50 -60 -20 -30 -40 -50 -60 -20 EJECT ENTER/YES -30 -40 -50 -60 - - - SHIFT JOG SHUTTLE 9 A 10 B 11 C 12 D 13 E 14 F 15 G 16 H TRACK INPUT MASTER Operation Manual CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. "WARNING" "TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. " SAFETY INSTRUCTIONS 1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. [. . . ] "Completed!" appears on the display then the "Copy Paste" (or "Move Paste") message flashes. This means that the sound data has been copied (or moved) to the clipboard, and that the system is ready to proceed to the following paste process. The recorder is ready to paste if there is no problem with the COPY/CLIP (or MOVE/CLIP) process. At this stage, it is possible to check the sound data in which COPY/CLIP (or MOVE/CLIP) was executed. To check the data on the clipboard, refer to the instructions described in "Checking Data in the Clipboard". 6. Use the [CH STATUS/CH SEL] key to select the paste destination track. · There is no need to select a track when pasting on the same track. · The mono track is the only track in which the paste destination can be changed. The other condition in which the paste destination can be changed is when the data from two tracks (odd and even) next to each other (1-2, 3-4, 5-6, 7-8, etc. ) are copied (or moved) on the clipboard. The paste destination track can be changed by pressing the [CH STATUS/CH SEL] key in this case. 73 · Note that it is not possible to paste to the same track that was copied (or moved) when copying (or moving) multiple tracks (1-3, 5-8, etc. ), although it was possible in the cases described earlier. In this case, the track will not be changed even if the [CH STATUS/CH SEL] key is pressed. UNDO/REDO Paste Copy & Paste or Move & Paste can be undone and redone with the UNDO/REDO feature. · The data pasted can be undone (unpasted) by pressing the [UNDO/REDO] key after Copy & Paste (or Move & Paste). · Data pasted but undone (unpasted) can be redone (re-pasted) by pressing the [UNDO/REDO] key immediately after undoing the paste process. The data will return to the post-paste status when re-done (re-pasted). Turn the [JOG] dial to choose the paste repeat frequency. The desired number can be input in the "01" area of the "Repeat = 01" that is currently flashing. The maximum repeat frequency that can be input is 99 but this repeat frequency is automatically limited according to how much space is available on the disk. Simply put, a frequency of 99 repeat times can be input if there is enough disk space. If there isn't, then only the maximum allowable repeat frequency (size) for the remaining disk space can be input. It is not possible to go above this number even if the [JOG] dial is turned. <Caution> The UNDO/REDO feature is valid only when the recorder is in the STOP state. UNDO/REDO is no longer possible if the following procedures take place after Copy & Paste (or Move & Paste). When the AUTO PUNCH mode is ON and PLAY (or RECORD) mode is effected, and the point has already passed the AUTO PUNCH IN point. Press the [ENTER/YES] key. "Copy Paste" (or "Move Paste") flashes on the display. "Completed!" lights up when the data has been successfully pasted. 9. Press the [EXIT/NO] key (or [STOP] key). The system exits from the edit mode and returns to the original time base display. <Caution> Note that Copy & Paste (or Move & Paste) is not possible unless there is enough disk space to "UNDO/REDO", as explained in the next section. [. . . ] In the example below, tracks 1-4 and 9-12 are selected for the source channel and their signals sent for ping pong into tracks 15 and 16. Record digital signals of sampling frequency identical to that of the VF160EX. The VF160EX sampling frequency is 44. 1kHz/16 bit. In a sampling frequency other than 44. 1kHz/16 bit, it will be recorded with the wrong pitch. Time count will also be incorrect. Having trouble Editing? · A warning message appears although it was only execution of copy-clip (or move-clip) ? Correctly register the CLIPBOARD IN and OUT points. The relation between CLIPBOARD IN point and OUT point is "IN point<OUT point". If it is registered in reverse relationship, copy-clip (or move-clip) cannot be executed. · When copy paste (or move paste) is executed, the sound section located before head of the bar is missing? Use the ALIGN SEL function. If the "ALIGN SEL" function is used at executing copy paste (or move paste), the sound section located in front of the bar head can be included at pasting. [. . . ]