User manual FOSTEX LM16
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual FOSTEX LM16. We hope that this FOSTEX LM16 user guide will be useful to you.
You may also download the following manuals related to this product:
FOSTEX LM16 (3895 ko)
FOSTEX LM16 BROCHURE (1400 ko)
Manual abstract: user guide FOSTEX LM16
Detailed instructions for use are in the User's Guide.
[. . . ] 8588107000 (485793)
Model LM16
LIVE MIXER
Owners manual
<Note>: The LM16 will be upgraded to a new version for feature enhancement or improvement. Check the information about the latest software version from the Fostex website (http://www. fostexinternational. com/), Fostex service station or your local Fostex dealer. See page 36 for details about how to upgrade the software.
Model LM16
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. [. . . ] See page 31 for details.
(23) [EFFECT TO STEREO] control
Adjusts the output level from the internal effects to the stereo busses. See page 31 for details.
(24) [EFFECT TO AUX (1, 2, 3)] controls
17 18 19 20 21 22 23 24 25 26 28 27 29
Each control adjusts the output level from the internal effects to the corresponding AUX buss (1, 2 or 3). See page 31 for details.
(25) [AUX SEND] controls / [SOLO] switches
Each [AUX SEND] control adjusts the output level of the corresponding AUX SEND (1, 2 or 3) output. Each [SOLO] switch allows you to monitor the soloed signal of the corresponding AUX SEND (1, 2 or 3) output. Each press of the switch toggles between on and off (See page 30 for details).
(26) [MONITOR] control
Adjusts the output level of the [MONITOR (L/R)] and [PHONES] jacks. The output level of the [PHONES] jack is controlled by the [PHONES] and [MONITOR] controls (See page 32 for details).
(27) [EFF SEND] control / [SOLO] switch
Adjusts the output level of the EFFECT SEND . Each [SOLO] switch allows you to monitor the soloed signal of the EFFECT SEND output. Each press of the switch toggles between on and off.
(28) [ASSIGN TO STEREO OUT] switches
Each switch allows you to send the post signal of the corresponding GROUP fader to the [STEREO OUT L/R] jacks. When the switch is down, the signal is sent ( See page 33 for details).
(29) [OUTPUT LIMITER] switch
Activates or deactivates the limiter function for all the buss outputs (stereo L/R outputs, group outputs 1 through 4, Aux send outputs 1 through 3, effect send output, and monitor outputs). When the switch is down ( ), the limiter function is active.
30
31
(30) [GROUP 1-4] faders
Each fader adjusts the output level of the corresponding group output signal which is output from the [GROUP OUT] jack (See page 33 for details).
(31) [STEREO] fader
Adjusts the output level of the stereo output signal which is output from the [STEREO OUT (L/R)] and [ST MIX OUT (L/R)] jacks.
24
Model LM16 [Names and functions]
Control unit (rear panel)
1
(1) [TO CONTROLLER] connector
Used to connect to the [CONTROLLER] connector of the main unit using the supplied (or a different) CAT5 cable (See page 13 for details).
<Note>: Use only a CAT-5 STP cable (straight type) for connection between the main unit and the control unit.
Main unit (rear panel)
1
INPUT
GROUP (+4dBu)
EFF SEND (-2dBu)
AUX SEND (-2dBu)
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
R STEREO OUT (+4dBu) L
ST MIX OUT (-10dBV)
USB
MIDI OUT
CONTROLLER
PHANTOM
POWER
13
12 11
10 9
8
7
6
5
4
3
2
(1) [INPUT (1 through 16)] connectors
Each connector accepts a mic or line level analog audio signal. The connector is a combo type - a combined XLR connector and phone jack in one. You can connect a microphone to the XLR connector or connect a line signal to the phone jack. (Note that you cannot use the XLR receptacle and phone jack on a same combo connector simultaneously. ) See page 28 for details.
(3) [AC IN] connector
Used to connect the supplied power cord (See page 15 for details).
<Note>: Use only the supplied power cord.
A different power cord may cause fire, etc. Also note that when you hear thunder rumbling, disconnect the power cord from the AC outlet.
(4) [POWER] switch (2) [INSERT (1 through 8)] jacks
Each jack is used for connecting an external effects processor such as a compressor/limiter. To connect an external effects processor, use a Y-cable as shown below ( See page 31 for details). Turns on or off the LM16 (See page 15 for details).
<Note>: Do not turn off the LM16 while accessing the internal hard disk. Even if you turn off the LM16, it consumes a very small amount of power. Therefore, it is recommended to disconnect the power cord from the AC outlet if you do not use the LM16 for a long time.
25
Model LM16 [Names and functions]
(5) [PHANTOM (1-8, 9-16)] switches
You can supply phantom power to the XLR INPUT connectors in eight channel groups (1-8 and 9-16) using these switches. When the [PHANTOM] switch is set to ON, the corresponding [PHANTOM] indicator on the control panel is illuminated (See page 28 for details).
(13) [STEREO OUT (L, R)] connectors
These XLR balanced connectors output the stereo L and R buss signals. You can connect these connectors to a power amplifier for driving main speakers on stage, etc (See page 16 for details).
(6) [CONTROLLER] connector
Used to connect to the [TO CONTROLLER] connector on the rear panel of the control unit using the supplied (or a different) CAT-5 cable (See page 13 for details).
(7) [AUX SEND (1, 2, 3)] jacks
Each of these unbalanced phone jacks outputs the corresponding AUX SEND buss signal at -2dBu nominal level. You can connect to a stage monitor, effects processor, etc (See page 16 for details).
(8) [MIDI OUT] port
Used to connect to the MIDI IN port of an external MIDI device. From this port, MMC (MIDI Machine Control command) is output (See page 40 for details).
(9) [EFF SEND] jack
This unbalanced phone jack outputs the EFFECT buss signal at -2dBu nominal level. [. . . ] You may also have additional rights depending on the state in which the Fostex product was purchased.
WARRANTY PROTECTION
All Fostex parts are warranted for one (1) year from the date of original purchase, except for recording media, such as hard disc drives and compact flash cards, heads, lamps and fuses, which are warranted, for one hundred-eighty (180) days. Fostex America will repair and / or replace parts during the term of this warranty. Labor costs are also covered by Fostex America for one (1) year from the date of original purchase. Except as specified below, this warranty covers all defects in material and workmanship in this product. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FOSTEX LM16
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual FOSTEX LM16 will begin.