User manual FORD MUSTANG-2002

[. . . ] Table of Contents Introduction Instrument Cluster Warning and control lights Gauges 3 10 10 15 Entertainment Systems AM/FM stereo cassette with CD AM/FM stereo with CD AM/FM stereo cassette (CD changer compatible) 19 19 28 43 Climate Controls Lights Headlamps Turn signal control Bulb replacement 63 67 67 70 71 Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control 76 76 77 78 80 80 Locks and Security Keys Locks Anti-theft system 89 89 89 91 Seating and Safety Restraints Seating Safety restraints Air bags Child restraints 99 99 102 114 119 Driving Starting 133 133 1 Table of Contents Brakes Traction control/AdvanceTrac Transmission operation Vehicle loading Trailer towing 138 142 144 154 156 Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Changing tires Jump starting Wrecker towing 157 157 158 159 160 165 170 175 Customer Assistance Reporting safety defects (U. S. only) 176 186 Cleaning Maintenance and Specifications Engine compartment Engine oil Battery Fuel information Part numbers Refill capacities Lubricant specifications 187 194 197 199 203 214 237 238 240 Accessories Index 245 248 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation. [. . . ] Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. 127 Seating and Safety Restraints The rear seats of your vehicle are equipped with built-in tether strap anchors located behind the seats on the package tray behind the speakers (coupe) or on the lower backside of the seatback (convertible). The tether anchors in your vehicle are either located under a cover marked with the child tether anchor symbol (shown with title) or are under a flap in the convertible top boot. The tether strap anchors in your vehicle are in the following positions (shown from top view): Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor. 1. For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, otherwise route the tether strap over the top of the seatback. Locate the correct anchor for the selected seating position as shown previously. 128 Seating and Safety Restraints For Coupe only: 4. Clip the tether strap to the anchor as shown. For Convertible only: The tether anchors on the convertible are located on the lower backside of the seatback. 4. Access tether anchors located behind the seatback and pull away vinyl flap to expose anchors. Clip the tether strap to the anchor as shown. 129 Seating and Safety Restraints If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for further instructions to secure the child safety seat. Tighten the child safety seat tether strap according to the manufacturer's instructions. If the safety seat is not anchored properly, the risk of a child being injured in a collision greatly increases. Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments (if equipped) Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. This type of child seat eliminates the need to use safety belts to attach the child seat. For forward-facing child seats, the tether strap must also be attached to the proper tether anchor. See Attaching safety seats with tether straps in this chapter. 130 Seating and Safety Restraints Your vehicle has LATCH anchors for child seat installation at the seating positions marked with the child seat symbol. The LATCH anchors were not designed to be used with a child seat in the center position and there is no tether anchor available at the center. Putting a child seat in the center would also block access to the safety restraint buckles. Use as a seating position, with or without a child restraint, may increase the risk of injury or death. Never attach two LATCH child safety seats to the same anchor. In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death. 131 Seating and Safety Restraints The lower anchors for child seat installation are located at the rear section of the rear seat between the cushion and seat back. [. . . ] Refer to your scheduled maintenance guide to determine the correct service interval. ENGINE DATA Engine Cubic inches Required fuel Firing order Spark plug gap 3. 8L OHV V6 engine 232 87 octane 1-4-2-5-3-6 1. 3-1. 4 mm (0. 052-00. 056 inch) EDIS 9. 4:1 4. 6L SOHC V8 engine 281 87 octane 1-3-7-2-6-5-4-8 1. 3-1. 4 mm (0. 052-00. 056 inch) Coil on plug 9. 4:1 1 Ignition system Compression ratio VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height (4) Wheelbase (5) Track - Front (5) Track - Rear 1 2 Coupe mm (in) 4653. 3 1856. 7 1348. 7 2573. 0 1534. 2 1539. 2 (183. 2) (73. 1) (53. 1) (101. 3) (60. 4) 1 (60. 6) 2 Convertible mm (in) 4653. 3 (183. 2) 1856. 7 (73. 1) 1351. 3 (53. 2) 2573. 0 (101. 3) 1534. 2 (60. 4) 1 1539. 2 (60. 6) 2 1521. 5 mm (59. 9 in) for Mustang GT 1526. 5 mm (60. 1 in) for Mustang GT 242 Maintenance and Specifications 3 5 2 4 1 IDENTIFYING YOUR VEHICLE Certification label The National Highway MFD. DATE: XXXXX GVWR:XXXXXXXXXXXX Traffic Safety FRONT GAWR: XXXXXX/XXXXXXX REAR GAWR: XXXXXXX/XXXXXXX Administration THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL MOTOR VEHICLE SAFETY, BUMPER, AND THEFT PRERegulations require VENTION STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE. that a Certification VIN: XXXXXXXXXXXXXXXXXX XXXXX TYPE: XXXXXXXXXXXXXXX XXXXX label be affixed to a vehicle and prescribe where the Certification EXT PNT: XXXXXX XXXXXX RC: XX DSO: XXXX BAR INT TR TP/PS R AXLE TR SPR label may be located. [. . . ]