User manual FORD CROWN-VICTORIA-2002

[. . . ] Table of Contents Introduction Instrument Cluster Warning and control lights Gauges 4 10 10 17 Entertainment Systems AM/FM stereo AM/FM stereo cassette AM/FM stereo with CD AM/FM stereo cassette (CD changer compatible) CD changer 22 22 26 33 39 49 Climate Controls Manual heating and air conditioning Electronic automatic temperature control 54 54 56 Lights Headlamps Turn signal control Bulb replacement 63 63 65 65 Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control Message center 72 72 73 74 75 79 83 Locks and Security Keys Locks Anti-theft system 91 91 91 93 1 Table of Contents Seating and Safety Restraints Seating Safety restraints Air bags Child restraints 104 104 108 122 127 Driving Starting Brakes Traction control/AdvanceTrac Air suspension Transmission operation Vehicle loading Trailer towing Recreational towing 137 137 141 144 146 146 151 152 155 Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Changing tires Jump starting Wrecker towing 156 156 157 158 159 164 169 174 Customer Assistance The dispute settlement board Utilizing the mediation/arbitration Getting assistance outside the U. S. and Canada Ordering additional owner's literature Reporting safety defects (U. S. only) 175 178 180 181 182 183 2 Table of Contents Cleaning Cleaning your vehicle Underbody preservation 184 184 189 Maintenance and Specifications Hood Engine compartment Engine oil Battery Fuel information Air filter(s) Part numbers Refill capacities Lubricant specifications Engine data Vehicle dimensions 191 192 192 193 197 206 219 224 225 226 228 228 Accessories Index 231 233 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. [. . . ] To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard. 6. The belt will click as it retracts to indicate it is in the automatic locking mode. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward and back. There should be no more than one inch of movement for proper installation. Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode (you should not be able to pull more belt out). If the retractor is not locked, unbuckle the belt and repeat steps two through nine. Check to make sure the child seat is properly secured before each use. To lengthen the belt, hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing. Route the tongue and webbing through the child seat according to the child seat manufacturer's instructions. Insert the belt tongue into the proper buckle for the center seating position until you hear a snap and feel it latch. Make sure the tongue is securely fastened to the buckle by pulling on tongue. Push down on the child seat while pulling on the loose end of the lap belt webbing to tighten the belt. Before placing the child into the child seat, forcibly tilt the child seat from side to side and in forward direction to make sure that the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward and back. There should be no more than one inch of movement for proper installation. Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. The rear seats of your vehicle are equipped with built-in tether strap anchors located behind the seats as described below. The tether anchors in your vehicle are located under a cover marked with the tether anchor symbol (shown with title). [. . . ] Service refill capacities are determined by filling the rear axle 6 mm to 14 mm (1/4 inch to 9/16 inch) below the bottom of the filler hole. LUBRICANT SPECIFICATIONS Item Brake fluid Ford part name Motorcraft High Performance DOT 3 Motor Vehicle Brake Fluid 1 Silicone Lubricant Ford part number PM-1 Ford specification ESA-M6C25-A and DOT 3 Door weatherstrips Engine coolant Engine oil F7AZ-19G208-BA ESR-M13P4-A and F5AZ-19553-AA Motorcraft VC-4­A (US) or ESE-M97B44-A Premium Engine CXC-10 (Canada) Coolant (green-colored) Motorcraft VC-7­A WSSPremium Gold M97B51­A1 Engine Coolant (yellow-colored) Motorcraft SAE XO-5W20-QSP WSS-M2C153-H with API 5W-20 Premium Certification Synthetic Blend Motor Oil Mark 226 Maintenance and Specifications Item Hinges, latches, striker plates, fuel filler door hinge and seat tracks Lock cylinders Power steering fluid Automatic transmission (4R70W) Rear Axle Lubricant 2 Ford part name Multi-Purpose Grease Ford part Ford number specification XG-4or ESR-M1C159-A F5AZ-19G209-AA Windshield washer fluid Penetrating and Lock Lubricant Motorcraft MERCON ATF Motorcraft MERCON V ATF3 Motorcraft SAE 80W-90 Premium Rear Axle Lubricant Ultra-clear Windshield Washer Concentrate Motorcraft XL-1 XT-2-QDX XT-5-QM none MERCON MERCON V XY-80W90-QL WSP-M2C197-A C9AZ-19550-AC ESR-M17P5-A Use only brake fluids certified to meet Ford specifications. However, if DOT 3 is not available, DOT 4 fluid can be used. 2 Add 118 ml (4 oz. ) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST-M2C118-A for complete refill of Traction-Lok rear axles. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle. [. . . ]