User manual FITNESSQUEST GAZELLE POWER PLUS ASSEMBLY

[. . . ] HYDRAULICS INSTALLATION PARTS (after complete unit is assembled) fastener pack mounting brackets M8 x 70mm hex bolts, washers and nylon nuts washers (4) 12mm springs clips 1/20/05 We recommend having someone available to help you. Due to the size and weight of some of the pieces, assembly is easier and safer if there are two people. nut caps hydraulics pin left right closed end wrenches washers (2) 8mm ASSEMBLY INSTRUCTIONS nuts Occasionally our products contain components that are pre-lubricated at the factory. We recommend that you protect flooring, or anything else the parts may contact, with newspaper or cloth. rubber pad (4) Tools Required for Assembly: Phillips Screwdriver Wrenches (provided) poly bag TO INSTALL YOUR HYDRAULICS RESISTANCE LEVELS NOTE: There are 4 levels of resistance on the unit. [. . . ] Second, use 4 of the M8 x 25mm bolts, 2 on each end, to attach the cross tube to the top of the base frame. d. Pull left hydraulic down to allow pin to pass through resistance hole in mounting bracket. For ease of assembly, raise foot platform slightly so pin can reach mounting bracket. Repeat Steps d and e on right side. Third, attach the frame plates to each side of the base frames using (4) M10 x 95mm hex bolts and spring washers from the fastener pack. Tighten bolts. clip in zero resistance remove 6 M8 x 25mm bolts from right base b. Lying Out Swing Arms replace 2 M8 x 25mm bolts to attach cross tube Move the left and right swing arms to the center of the frame assembly as shown. Make sure the cables lay on the top of all pieces. M10 x 95mm hex bolts front foot platform tube remove 6 M8 x 25mm bolts from left base replace 2 M8 x 25mm bolts to attach cross tube frame plate left frame right frame cross tube pin clip right base frame mounting bracket M10 x 95mm hex bolts frame plate left base frame left swing arm right swing arm ©2003, ©2004 and ©2005 Fitness Quest ® Inc. Gazelle Power PlusTM is a trademark of Fitness Quest® Inc. left frame front c. Left Frame/Swing Arm Assembly Raise the left frame (marked with the L and arrow facing the front) and secure it onto the left base frame using (4) of the M8 x 25mm hex bolts and spring washers you removed in step a. When tightening these bolts, you can use the wrenches provided in either the fastener pack or the hydraulics fastener pack ­ whichever works best for you. Electronics Assembly Step 1: Remove the two small screws from the bottom of the electronics with the screwdriver provided. Step 2: Attach the bottom housing with the large bolt provided in the bag with the batteries as shown. Step 3: From the front of the unit, place the top housing onto the bottom housing and replace the two small screws you removed in Step 1 as shown. Step 1 Step 2 view as if you are using the unit Step 3 M8 x 25mm hex bolt and spring washer left base frame Remove the two small screws left swing arm axle tube right swing arm d. Axle Tube Assembly Raise the left swing arm up to the top of the left frame. Make sure the arrow on the axle tube is pointing left and the notch on the end of the axle tube is down. IMPORTANT: Slip a large washer onto the axle between the swing arm and the left frame before inserting the axle tube into the left frame. [. . . ] Secure everything onto the axle tube with the M8 x 25mm hex bolt, spring washer and washer that is left from your fastener pack. tab end cap front view Attach the end cap onto the frame using a M6 x 40mm Phillips bolt in the lower hole only. Align the water bottle holder on the end cap so the tab on the back of the holder fits into the bottom hole of the end cap. Attach the other end cap with (2) M6 x 40mm Phillips bolts. view as if stepping on unit front right base frame Slip the right frame onto the base frame assembly and secure it using the M8 x 25mm hex bolts and spring washers you removed in step a. [. . . ]