User manual FIRST ALERT FA2100C 7-96

[. . . ] Previous N8031-1 7/96 SYSTEMOVERVlEW TABLE OF CONTENTS 3 BYPASSINGBURGLARYPROTECTlONmES usi?g-~As-Y --. . . -- . 18 18 FimLElmgemy-. "". . A "-. ". . -. --5 -. . . _I 3 4 4 5 6 TmcALALPHAKEYPAD FIXED-WORD KEYPADDISPLAYS. RmcmD= DumsscodR. ---". --ckidtm ToAss&. , orDebteUserCcxks REMoTEKEYPADEMERGENcY -. . . -. . . I----3 -----3 . ---. "_. . . . 10 ONLY (STAG: s~-BuRGLARYPRoONLY (INSTAlflJ-. 2l AARMINGPERlMElER BURG. PROTECTION P PROTECTION (AWAY). . . . -. -. . . --. --ARMINGALLBURGLARY 23 ARMlNGAUBURGlARY pMymmoN (MAxlMUM). . ". "~~. ". " DMR&tl~~LARY PROTECTION. [. . . ] If the display will not clear and does not provide a "Ready" message, notify the alarm agency. See the SUMMARY OF AUDIBLE/VISUAL NOTIFICATION section for information which will. help you to distinguish between FIRE and BURGLARY alarm sounds. IMPORTANT: If you . return and the main burglary sounder is on, DO NOT ENTER, but CONTACT THE POLICE from a nearby safe location. If you return after an alarm has occurred and the main sounder has shut itself off, the keypad will beep rapidly upon your entering, indicating that an alarm has occurred during your absence. LEAVE IMMEDIATELY, and CONTACT THE POLICE from a nearby safe location. -24- BURGLARY PROTECTION EXIT ALARMS Burglary Protection Exit Alarm Warning Displays and Sounds The burglary protection portion of your system may have been programmed for this feature. When arming your burglary protection, if an exit or interior zone contains a fault during closing at the time the exit delay ends, the alarm sounder and keypad sound continuously to alert you that an unwanted alarm can be prevented if you take action: l If you disarm the burglary protection during the entry delay period that will immediate/y follow, the sound stops. The keypad displays `CANCELLED ALARM "or "CA" as well as a zone indication. l If the burgiary protection is NOT disarmed during the immediately following entry delayperiod, the sounds continue until the system is disarmed (or alarm sounder timeout occurs). The keypad displays "EXIT ALARM" or "EA" as well as a zone indication. An "exit alarm" messaae will be sent to the central station. Note: The latter "EXIT ALARM" conditions also result if an alarm from an exit or interior zone occurs within two minutes after the end of an exit delay. In any of the above cases, a second OFF sequence (user code + OFF key) will clear the keypad display. -25- EMERGENCY AND 24 HOUR NON-FIRE ALARMS General Your system may have sensors which detect non-fire related alarm conditions, such as the triggering of an HVAC (Heating, Ventilating, or Air Conditioning) temperature sensor, the pressing of a holdup alarm button, etc. Your system may provide some or all of the indications listed `below, depending on what your installer selected to occur when one of those conditions is detected. if your system's keypad has any active emergency alarm key(s) (see REMOTE KEYPAD EMERGENCY KEYS on page 11) these indications may be manually triggered by pressing the appropriate emergency key (or corresponding emergency key pair). l The keypad buzzer produces a steady sound (no sound for silent alarms). l The external alarm sounders produce a steady sound (no sound for silent alarms). l The keypad LCD (Fixed-Word) displays the word "ALARM" and the zone number in alarm. Alpha keypads also display a description of the zone in alarm (no keypad displays for silent alarms). -1 1 l ALPHA FIXED-WORD An emergency alarm message is sent to the central station. To reset the keypad alarm display: First correct the cause of the alarm condition, and then: Re-enter your User Code, followed by the OFF key. Silencing and Resetting an Emergency Alarm To silence the keypad buzzer and external alarm sounders: Enter your User Code, followed by the OFF key. The kevoad's LCD will disolav the number--of the zone in atarm as a Memory of Alarm indication. -26- SUPERVISORY CONWTIONS General If your building has a fire sprinkler system, your installer may have installed a sensor which monitors the sprinkler system (e. g. , to determine whether the main water gate valve is open or that there is adequate water pressure, etc. ). [. . . ] They do create multiple beams of protection, and intrusii can on be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind w afy ceilings, floors, dosed doors!Mechanical tampering, masking, painting or spraying k, of any matenal on the mirrors, wmdows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90" to 105°F (32" to 40°C). [. . . ]