User manual FIRST ALERT FA2000C 7-96

[. . . ] Previous Menu USER'S MANUAL FA2000C Fire Alarm Control/Communicator N8028-1 7/96 TABLE OF CONTENTS SYSTEM OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Fire & Emergency Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] CALL YOUR INSTALLER IMMEDIATELY FOR SERVICE, WHEN ANY OF THESE INDICATIONS APPEAR FOR A CONDITION THAT CANNOT BE CORRECTED BY YOU! The control's buzzer and keypad buzzer both produce a rapid pulsing sound. The controls AC POWER LED turns off and the keypad LCD displays "AC LOSS" (Alpha) or "NO AC" (Fixed-Word) when AC power is low or not present. The control's BATTERY TROUBLE LED lights and the keypad LCD displays "SYSTEM LO BAT" (Alpha) or "BAT" (Fixed-Word) when your system's back-up battery is low or disconnected. The controls COMM FAIL LED lights and the keypad LCD displays "COMM FAILURE" (Alpha) or "FC" (Fixed-Word) when attempts to send a message to the central station have failed. The keypad LCD (Fixed-Word) displays "CHECK" accompanied by a protection zone number (15) or system zone number (612) when there is a zone or system related problem. The control's LINE FAULT LED lights if the problem is with the telephone lines. CHECK 03 CHECK 01 FRONT UPSTAIRS STORAGE WAREHOUSE SMOKE ALPHA 03 ALARM FIRE CHECK AWAY BYPASS STAY INSTANT SUPV NO AC PHONE TEST NOT READY CHIME BAT TAMPER FIXED-WORD 19 TROUBLE CONDITIONS A trouble message is sent to the central station. Note: If your keypad LCD displays "0C" for more than 5 minutes, then it is not receiving signals from the control. Silencing and Resetting a Trouble Indication To silence the control and keypad buzzers: Press the control's SILENCE/RESET button or enter your User Code, + the OFF key. To reset the keypad trouble display: First have the cause of the trouble condition corrected, and then: Press the SILENCE/RESET button again or re-enter your User Code, followed by the OFF key. The keypad's LCD will display the number of the zone in trouble as a Memory indication. 20 ACTIVATING A FIRE DRILL TEST Using the # + 6 + 9 Keys This feature can be activated only while no alarm, supervisory, or trouble condition is present. This test requires that a keypad and external fire alarm sounder be installed with the system. This test activates the external fire alarm sounders for the purpose of conducting a fire alarm drill. Your system will remain operational for fire alarm signaling while this test is active (although no message will be sent to the central station unless an actual alarm occurs). To activate the Fire Drill Test: Enter User Number 2's code, then press the # + 6 + 9 keys. The keypad LCD will display "FIRE DRILL ACTIVE (Alpha) or "TEST dF" (Fixed-Word) and the external fire alarm sounders will produce either a steady or a pulsing sound while this test is active, depending on what your installer selected. FIRE DRILL ACTIVE ALPHA dF ALARM FIRE CHECK AWAY BYPASS STAY INSTANT SUPV NO AC PHONE TEST NOT READY CHIME BAT TAMPER FIXED-WORD To terminate the Fire Drill Test: Enter any User Code, followed by the OFF key. Your system will also automatically terminate this test if an alarm, supervisory or trouble condition is detected while it is activated. 21 QUICK GUIDE TO SYSTEM FUNCTIONS FUNCTION Silence Alarm, Supervisory or Trouble sounds Reset Smoke Detectors & Displays Manually Trip Emergency Alarms Bypass Emergency Zone(s) Fire Drill Test PROCEDURE Press the SILENCE/RESET button or Enter user Code + OFF key. Press the SILENCE/RESET button a second time or Re-enter user Code + OFF key. Press key [A], [B], or [C] for at least 2 sec. , or press keys [1]&[ D], or [ D]&[#], or [3]&[#], both at same time. To bypass , enter user code + BYPASS key + zone number(s) (use 2-digit entries). To turn off: Enter any user code + OFF key. COMMENTS SILENCED LED lights. Will reset only if fault corrected. Key(s) must be enabled by installer. Bypassed zones will not cause an alarm if violated. Activates external fire alarm sounders. Assign, change, To assign or change: Enter User Number To delete : Enter User Number 2's code + CODE key + or delete user 2's code + CODE key + user number (26) user number (36) and stop. change but not delete his/her own code. 22 SUMMARY OF AUDIBLE/VISUAL NOTIFICATION ALPHA & FIXED-WORD DISPLAY KEYPADS SOUND SLOW PULSING Keypad and, as selected by installer: SLOW PULSING or STEADY External, STEADY Keypad & External a. ALARM plus number and descriptor of zone in alarm (ALARM plus zone #). CAUSE a. FIRE DRILL DISPLAY (Fixed-Word displays are shown in parentheses) a. [. . . ] The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. Wireless transmitters (used with some systems) are designed to provide long battery life under normal operating conditions. Longevity of batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device being used. [. . . ]