User manual FESTOOL PSBC 400 EBC

[. . . ] Hour minutes seconds kilograms diameter tip, hint Degree centigrade Newton metre millimetre amps hour watt hour delay fuse with 4 amps Warning of general danger Risk of electric shock Safety instructions General safety instructions wARNING!Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. B) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. [. . . ] Risk of injury, electric shock X Always disconnect the battery pack before any type of work on the machine! Using the chip guard The chip guard [1-1] prevents chips flying away and improves the efficiency of the chip extraction system. The number of strokes can be adjusted steplessly with the adjusting wheel [1-5] between 1500 and 3800 rpm (PSBC 400 EB: 1000 - 3800 rpm). This enables you to optimise the cutting speed to suit the respective material. In position A, the automatic load detection is activated: The stroke speed is reduced in idling and is controlled to the highest value when the blade enters the workpiece. Recommended stroke speed (position of the adjusting wheel) Hard and soft wood, plywood board, plywood, chip board Hardboard Plastic Ceramic, aluminium, non-ferrous metals Steel A 4-A 3-A 3-5 2-4 Instead of the saw table, the angle table WT-PS 400 or adaptation table ADT-PS 400 can be installed at the support. Never saw without the saw table, or one of the other tables offered in the Festool accessories program. The splinterguard makes cuts with splinter-free cutting edges possible, even on the exit side of the saw blade. X With the machine switched off, push the splinterguard [4-1] onto the guide up to the saw blade [4-2], X switch on the jigsaw, X with the machine running (stoke speed position 5), push the splinterguard in on a flat plane until it is flush with the front edge of the saw table. In order to process different materials with an optimum feed movement the pendulum jigsaws have an adjustable pendulum stroke. Select the desired setting with the pendulum stroke switch [1-11]: setting 0 = pendulum stroke off setting 3 = maximum pendulum stroke Recommended settings of the pendulum stroke Hard and soft wood, chip board, wood fibre 1-3 board X Insert the extraction adapter into the rear opening of the saw table so that the hook [5-2] engages in the [5-1] recess. Deformed or cracked saw blades and saw blades with blunt or broken cutting edges must not be used. The saw blade should not be longer than that required for the intended cut. To ensure safe guidance, during the cut the saw blade should emerge at the bottom of the workpiece at every point. L To guarantee reliable operation of the splinterguard, it must seal tightly on both sides of the saw blade. For splinter-free cuts, therefore, a new splinterguard should also be used after every saw blade change. X Always read applicable national regulations before extracting hazardous dust. L Only use cross-set saw blades when using the angle and adapter table. Risk of injury, electric shock X Always disconnect the battery pack before any type of work on the machine!X Once the battery pack has cooled, perform a functional check using the charger. Use only original Festool accessories and Festool consumable material intended for this machine because these components are designed specifically for the machine. Using accessories and consumable material from other suppliers will most likely affect the quality of your working results and limit any warranty claims. [. . . ] Even after disconnection from the mains, there is still a high capacitor voltage inside the charger. Damaged safety devices and components must be repaired or replaced in a recognised specialist workshop, unless otherwise indicated in the operating manual. Observe the following instructions: ­ Keep the air slits on the machine and the charger free and clean to ensure adequate cooling. The equivalent amount of lithium in the LiIon battery pack is less than the applicable limit value and certified as per UN manual ST/SG/ AC. [. . . ]