User manual FESTOOL LA

[. . . ] 4 Emission levels Levels determined in accordance with EN 60745 are typically: Sound pressure level Noise level Uncertainty LPA = 88 dB(A) LWA = 99 dB(A) K = 3 dB Operating noise Damage to hearing X Use ear protection!Vibration emission value ah (vector sum for three directions) and uncertainty K measured in accordance with EN 60745: ­ Wear suitable protection such as ear protection, safety goggles, a dust mask for work which generates dust, and protective gloves when working with raw materials and when changing tools. ­ Always secure the workpiece in such a manner that it cannot move while being sawed. The PSB 400 EBQ also has a variable speed trigger [1-3] with switch lock [1-4]. [. . . ] Inserting saw blade Always pull the mains plug out of the socket before changing blades. X Push the saw blade [3-4] into the opening as far as the stop with its teeth in cutting direction [3-2]. L In the case of very short saw blades, it is advisable to remove the saw table (see chapter 7. Risk of accident X The mains voltage and the frequency of the power source must correspond with the specifications on the machine's name plate. X In North America, only Festool machines with the voltage specifications 120 V/60 Hz may be used. The electric power tool has one button [1-2] on each side for switching on/off. Ejecting saw blade L When ejecting the saw blade, hold the electric power tool such that no persons or animals can be injured. If the saw blade is not ejected: run jigsaw 3 - 10 seconds at a high speed. 2 Using the chip guard The chip guard [3-1] prevents chips flying away and improves the efficiency of the chip extraction system. 3 Inserting splinterguard The splinterguard makes cuts with splinterfree cutting edges possible, even on the exit side of the saw blade. X With the machine switched off, push the splinterguard [4-1] onto the guide up to the saw blade [4-2], X switch on the jigsaw, X with the machine running (Speed range 5), push the splinterguard in on a flat plane until it is flush with the front edge of the saw table. The stroboscope light may make it difficult to determine the saw blade position Risk of injury X Ensure the work area is well illuminated. Use only original Festool accessories and Festool consumable material intended for this machine because these components are designed specifically for the machine. Using accessories and consumable material from other suppliers will most likely affect the quality of your working results and limit any warranty claims. Machine wear or your own personal workload may increase depending on the application. Protect yourself and your machine, and preserve your warranty claims by always using original Festool accessories and Festool consumable material!The order numbers of the accessories and tools can be found in the Festool catalogue or on the Internet under "www. 1 Saw blades, other accessories In order to saw different materials quickly and cleanly, Festool offers saw blades for all applications that are specially designed for your Festool jigsaw. Sawing with special base runners The special base runners protect high-quality surfaces against scratches and scores. 3 Sawing with the angle table The angle table WT-PS 400 is used for sawing interior and exterior angles up to 45° and pipes. Sawing with the adaptation table The adaptation table ADT-PS 400 is used for attaching your jigsaw to the Festool guide rail, the circle cutter KS-PS 400 and the CMS modular system. Adaptation to the guide rail FS The use of the Festool guide system FS (Picture [9]) makes it easier to produce straight and precise cuts, in particular, with material thicknesses up to 20 mm. [. . . ] EU only: European Directive 2002/96/EC stipulates that used electric power tools must be collected separately and disposed of at an environmentally responsible recycling centre. We offer a warranty for material and production defects for all our tools in accordance with the locally applicable legal provisions, but for a minimum of 12 months. Within the EU member states, the warranty period is 24 months (verification through invoice or delivery note). Damage caused by the operator, natural wear, overloading, incorrect handling or through the use of the equipment not specified in the operating manual, or damage which was known at the time of purchase, is not covered by the warranty. [. . . ]