User manual FESTOOL CS 50 EB FLOOR

[. . . ] EC-Declaration of Conformity: We declare at our sole responsibility that this product is in conformity with the following standards or standardised documents: EN 61029-1, EN 61029-2-1, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 610003-3 in accordance with the regulations 2006/42/EC, 2004/108/EC. Bench-mounted circular saw and circular trimming saw CS 50 EB/CS 50 EB Floor Technical data Cutting depth at 90°/45° Inclination max. Drawing length Saw blade (diameter x cutting width) Idling speed Power consumption Bench dimensions (length x width) Bench height with / without foldaway legs Weight without foldaway legs Weight of foldaway legs The specified illustrations can be found at the beginning of the operating instructions. 1 Symbols Warning of general danger Read the operating instructions/notes CS 50 EB/CS 50 EB Floor 0 - 50 mm/0 - 40 mm -2° to 47° 300 mm 190 x 2 , 6 mm 1600 - 4200 rpm 1200 W 600 x 400 mm 900 mm/375 mm 19 kg 2 kg b. [. . . ] The emission values specified refer to the main applications for which the power tool is used. If the electric power tool is used for other applications, with other tools or is not maintained sufficiently prior to operation, however, the vibration and noise load may be higher when the tool is used. Take into account any machine idling times and downtimes to estimate these values more accurately for a specified time period. This may significantly reduce the load during the machine operating period. 4 Residual risks In spite of compliance with all relevant design regulations, dangers may still present themselves when the machine is operated, e. : - Workpiece parts being thrown off, - Parts of damaged tools being thrown off, - Noise emission, - Sawdust emission. 4 Setting up, commissioning Ensure that the floor around the machine is level, in good condition and free of loose objects (e. 1 Mounting the machine The machine can be set up with or without the legs folded out (Fig. So that the machine stands securely, the length of one of the legs can be changed by turning the cap on the end (1. 3 Applications The machine can be used as a bench-mounted circular saw or as a circular trimming saw. 8) downwards, and use the hand grip to pull the saw unit forwards until it locks into place. The saw unit is now in a central bench position and the machine can be used as a bench-mounted circular saw. 9) is swung downwards, it can be used to move the saw unit backwards and forwards for drawing cuts. Dust extraction The PRECISIO has two extraction connections: the upper protective cover (2. The extraction set CS 70 AB (488292, included in scope of delivery for CS 50 EB) joins both of the extraction connections so that a Festool extractor module can be connected. In North America, only Festool machines with the voltage specifications 120 V/60 Hz may be used. For continuous operation after switching on, first press the ON/OFF switch (4. To switch off continuous operation, either press the ON/OFF switch again 18 4. To protect against unauthorised activation, a shackle type connector can be inserted in the hole (4. 5 Electronics The machine has full-wave electronics with the following features: 2 Speed adjustment You can regulate the speed steplessly between 1600 and 4200 rpm using the adjusting wheel (4. This enables you to optimise the cutting speed to suit the material (4. The pre-selected speed remains constant whether the machine is in operation or in neutral position. [. . . ] - On completion of your work, wind the power cable around the holders (2. - A damper means that the saw unit runs back evenly across the entire drawing length. If this is not the case, the damper can be adjusted through the hole (2. 9 Accessories, tools Use only original Festool accessories and Festool consumable material designed for this machine because these components are designed spe20 8 Adjust the protective hood so that it rests on the workpiece and clamp it in this position with the knob (1. [. . . ]