User manual FERGUSON TE-D20 SERVICE MANUAL

[. . . ] FERGUSON TECHNIK AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTAL DAMAGES IRRESPECTIVE OF WHETHER FERGUSON TECHNIK OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES. Page 3 Reference Manual TE-D20 Version 2. 0 Regulatory information Europe Declaration of Conformity We FERGUSON Technik AG Brunnenweg 3 D-64331 Weiterstadt Germany Declare under our sole responsibility that the product TYPE: TE-D20 To which this declaration relates is in conformity with the following standards (environments E1-E3): EN 55103-1 /1996 EN 55103-2 /1996 EN 60950 /2001 Following the provisions of 89/336/EEC and 73/23/EEC directives. Winfried Deckelmann Weiterstadt, August 2005 Place and date of issue Legal Signature USA FCC 47 Part 15 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to the part 15 of the FCC Rules. [. . . ] 16 Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Switch Function Detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Factory Preset Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Alarm/LED Status Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Module Edge Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Alarm Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Locate Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Auto Store. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Specifications (TE-D20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Available Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Page 5 Reference Manual TE-D20 Version 2. 0 This Page is intentionally left blank Page 6 Reference Manual TE-D20 Version 2. 0 Getting Started Packaging The shipping carton and packaging materials provide protection for the module during transit. Please retain the shipping cartons in case subsequent shipping of the product becomes necessary. Product Description The TE-D20 is a high quality 8 bit video digital to analog converter designed primarily for broadcast and professional applications. Three modes of operation are possible using the shared connections on the front panel, GBR, YUV or SVideo component analog outputs. The module also provides 3 composite outputs in parallel to the selected component analog output. The module provides two re-clocked SDI loop through signals for further use downstream. The TE-D20 has a variety of features, which include: · · · · · · · · · Component RGB or YUV or S video outputs 3 x Composite (CVBS) output PAL or NTSC operation Internal color bars Internal 2x over sampling (27MHz) 2 x reclocked SDI loop through outputs Local DIP-switches and LED's for control and status monitoring. Remote control and status monitoring of all modules is possible with the addition of the R CT 5020 rack controller and R CT 5030 master controller options. Please refer to the respective reference manuals for these options for details of mechanical installation. Please see the section following the table for more detail on the switch function. Switch 1 2 3 4 5 6 7 8 Setting ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF Function Local control enabled (toogle for reaquire) Local control disabled RGB component output YUV component output Selection on switch 2 enabled S- Video output Active line length 720 pixels Active line length 702 pixels Test signal ON (Color Bars) Test signal OFF (Color Bars) Test signal = NTSC format Test signal = PAL format If no input, output = BLACK If no input, output = color bars Not used Page 16 Reference Manual TE-D20 Version 2. 0 Switch Function Detail All settings are stored in Flash Ram inside the module (see Auto Store section in this manual). It is recommended that switch 1 is set to OFF to disable further local control when the module is configured for use. ON enables local control and makes selections on the dip-switch active, and OFF disables local control (locking out any changes). If local control is disabled from remote (LED 3 OFF), please toggle Dip Switch 1 to reaquire local control Dip Switch 2 This switch selects either RGB or YUV component analog outputs from the module. Dip Switch 3 This is used to select the Y/C (S-Video) output from the module. ON makes the selection on switch 2 active Dip Switch 4 Thisis used to set the active line length to either digital blanking or analog blanking . ON active line length 720 pixels (digital blanking), OFF active line length 702 pixels (analog blanking) Dip Switch 5 This will select the internal color bar test signal from the module which is available on all outputs in the video standard selected. Page 17 Reference Manual TE-D20 Version 2. 0 Dip Switch 6 Selects the output mode for the test signal. ON for NTSC, OFF for PAL Dip Switch 7 Selects the output signal if no input signal is present. ON selects signal BLACK, OFF selects signal COLOR BARS Factory Preset Condition The TE-D20 is delivered preset for the following mode of operation: · · · · · · Local control ENABLED YUV Output Active line length 720 pixels Test signal OFF Test signal format PAL If no input output signal = COLOR BARS If this is the mode of operation required, then no adjustments are necessary. Page 18 Reference Manual TE-D20 Version 2. 0 Alarm/LED Status Indicators The TE-D20 module has built in LED indicators, which serve as alarm and status indication for the module. [. . . ] Signal presence detection + 5VDC 3, 5 VA DC input via 5 pin locking bayonet connector IEC 60950/ EN 60950/VDE 0805 Outputs (digital) SDI Outputs Output Impedance Return Loss Output Level Jitter Outputs (analog) Analog Outputs Output Level Return Loss Signal to Noise Operating Modes Outputs TV Standard Test Sync Performance Control Status Monitoring Operating Voltage Power Consumption Connection Safety Electrical Specifications Mechanical Size Weight 85. 5mm x 35. 3mm x 27mm + connectors 150 g 5°C to 35°C Maintaining specifications -20°C to +70°C Storage Max 80% non condensing TE-D20 Reference Manual and quick ref guide Ambient Temperature Humidity Documentation Supplied Accessories Page 21 Reference Manual TE-D20 Version 2. 0 Available Options Below is a list of available options for the TE-D20 MiniModule. Please refer to product brochures or our web site for more detailed information. Model R PS 3001 E Description External brick power supply module for Series 3000 MiniModules. This is a basic 19 inch rack mountable frame which can accommodate 10 MiniModules with power bricks R PS 1 or can be extended with the R FR 3010. [. . . ]