User manual FENDER REISSUE 54 ESQUIRE

[. . . ] SWITCH OFF POWER TO THE UNIT AND UNPLUG THE AC POWER LINE CORD BEFORE CLEANING THE UNIT'S EXTERIOR. ALLOW THE UNIT TO COMPLETELY DRY BEFORE RECONNECTING IT TO THE AC POWER SUPPLY. KEEP 6 INCHES (15. 3 cm) OF UNOBSTRUCTED AIR SPACE BEHIND THE UNIT TO ALLOW FOR PROPER COOLING BY VENTILATION. FENDER AMPLIFIERS AND LOUDSPEAKERS ARE CAPABLE OF PRODUCING VERY HIGH SOUND PRESSURE LEVELS WHICH MAY CAUSE TEMPORARY OR PERMANENT HEARING DAMAGE. [. . . ] Select between 1. 0 to make each subsequent repeat darker and 10. 0 to allow the high frequencies to repeat. Use this control to simulate the high-frequency absorption of acoustically dull rooms or analog echo units. Note that because this control removes highs from the signal, that it will also affect the number of delayed repeats. e do M XF tid E t e se rP . . . . . . . . . . . . . . . . . . . . . LA U NA M N OI TC UR TS NI . . . . . . . . . . . . . . . . . . . . . . [ [ [ [ . Description 1, :7 5 ( %< & Try turning the Chorus Depth control to 1. 0 and actively adjusting Chorus Average Delay to achieve a comb-filter effect. / Adjustable parameters VWFHII( VXURK& VXU RK& HOJQDLU7 VX URK& HQL6 For "tape echo madness, " use the default Ramp setting, set the echo time and feedback to near maximum, and then - rotate the Echo Time (ms) (FX VAL 1) knob and listen. You will be able to get the swirly, warble, drunken pitch change to feed back through the echo the way countless tone masters have used the sliding tape head on vintage tape echo units in real time. You can also use a MIDI continuous controller pedal or expression pedal to control the echo time for the same effect. HG R0 ;) WL G ( W HV HU 3 34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjusts the amount of wow (random frequency response modulation) and flutter (random pitch change) present in the echo signal. Select between 1. 0 for minimum levels and 10. 0 for maximum levels of this effect. Note that by having this control in the higher part of its range, the wow and flutter will continue to operate over the repeats of the echo, causing compounded randomness. Select Ramp or Step to change the way the effect responds to changes in the Echo Time parameter. With the Ramp setting, the echo time change will be gradual with an analog sounding pitch warble, (audible until the delay time stabilizes). With the Step setting, the echo time change will be instant with a "digital zip" sound audible for a moment. [ [ [ [ [ [ [ [ ~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~ Stereo chorus effects with sine-wave or triangle-wave delay modulation. Select 10. 0 and the LFOs are out-of-phase and the maximum stereo effect is achieved. / Adjustable parameters ~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~ Description Adjustable parameters A tremolo with the sound of a vintage Blackface amp. Select between 1. 0 for 0% wet (no effect) and 10. 0 for 100% wet (all effect). The increment of change gradually increases from 0. 01 Hz for the slowest rate to 0. 08 Hz for the fastest rate. Remember that the TAP button can always be used to key in the tremolo rate by feel two TAPs set the time it takes for the LFO to go through one cycle. Select 1. 0 for minimum depth and 10. 0 for maximum depth. / . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . e do M XF tid E t e se rP . VWFHII( RORPHU7 . VWFHII( HJQDO) HJQDO) HOJQDLU7 RORPHU7 SP$ HJQDO) HQL6 LA U NA M N OI TC UR TS NI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description Adjustable parameters Description Adjustable parameters 1, :7 5 ( %< & QD3RWX$ RORPHU7 HG R0 )3 )4 )L )1 )2 )3 )4 )L )1 )2 ;) WL G ( W HV HU 3 36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjusts the Low Frequency Occilator maximum volume / minimum volume interval ratio. Select between 1. 0 for short high volume intervals and 10. 0 for long high volume intervals. Select between 1. 0 for a subtle and natural effect and 10. 0 for a choppy effect. ~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~ A sine-wave tremolo effect that can be used to approximate grid-bias tremolo or repeat percussion as found in a Tweed Tremolux. Select between 1. 0 for 0% wet (no effect) and 10. 0 for 100% wet (all effect). The increment of change gradually increases from 0. 01 Hz for the slowest rate to 0. 08 Hz for the fastest rate. [. . . ] . . . 1 2 /$ 8 1$ 0 CC# 07 32 85 96 97 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 Parameter Master Volume LSB for Bank Changes Effects/Reverb Bypass Data Increment Data Decrement Gain Volume Treble Middle Bass Presence Reverb Master Volume FX Level FX Val 1 FX Val 2 FX Val 3 FX Val 4 Reverb In [Dwell] Reverb Tone [Shape] Reverb Time Reverb Diffusion Tap Value Range (0 - 127) (0 - 127) OFF (0=63), ON (64-127) (Linked to the DATA WHEEL) (Linked to the DATA WHEEL) (0 - 127) (0 - 127) (0 - 127) (0 - 127) (0 - 127) (0 - 127) (0 - 127) (0 - 127) (0 - 127) (0 - 127) (0 - 127) (0 - 127) (0 - 127) (0 - 127) (0 - 127) (0 - 127) (0 - 127) Table Notes: Cyber-Twin continuous controller resolution: 0 127, (it will not accept 16, 384 step sizes). Data Increment/Decrement models the DATA WHEEL by 1/-1 increments V HF LG QH SS $ V HJQDK& PDUJRU3 , ', 0 * * * * [LGQHSS$ 1 2, 7& 85 76 1, 1, :7 V HJDVVH0 HYLVXOF[( PHWV\6 Note: All System Exclusive data values are displayed in hexadecimal with H for clarification. System Exclusive Header Value F0H 08H nnH 11H ffH F7H Description Start of System Exclusive Message Fender's Manufacturer ID nn = Device ID (minus one) Amp ID number 11H. The upper nibble identifies the Cyber-Twin and the lower nibble is the software version Function ID number. See table to the right for values. > End of System Exclusive Message Function ID Numbers 01H 02H 03H Description Utilities Message One Preset Message All Presets Message 5 ( %< & [LGQHSS$ Value F0H 08H nnH 11H ffH PnH Data CBH F7H Value F0H 08H nnH 11H ffH 7BH F7H System Exclusive Data Packet Description Start of System Exclusive Message Fender's Manufacturer ID nn = Device ID (minus one) Amp ID number 11H. [. . . ]