User manual FENDER 3206

[. . . ] On the original model, the Reverb / Vibrato Footswitch connected to the unit via 2 RCA style jacks; this has been changed to a more reliable 1/4" jack. The VIBROVERB is unique in Fender amplifier history by the implementation of its tone circuit. The VIBROVERB was the first and ONLY Fender amplifier to use this type of tone circuit. The treble control is "tapped, " meaning it responds more like an active tone control allowing boost AND cut of high frequencies. [. . . ] Conventional Fender tone circuits provide a small amount of tone shaping even in the "0" position, but if the VIBROVERB Treble Control is set to about "5", the response is flat. The speakers used in the `3206 are reproductions of the original speakers made by the Oxford Speaker Company. When Fender started work on this project, Fender contacted Oxford who still had much of the original tooling and documentation of this 10 inch speaker from the early sixties. The power and output transformers used in the `3206 are built to the original specifications, which are still in the R&D engineering files at Fender's office. The same "direct-coupled" oscillator circuit is used for generating the vibrato. The reverb sound from the VIBROVERB is "warmer" than later Fender amps due to the unique reverb send and recovery circuit. The cosmetics of the `3206 incorporate the brown "Tolex" and "Ecru" grill cloth used in 1963. We have retooled the "flat" Fender logo and have added the original tilt-back legs found on so many Fender amps through the sixties and seventies. It is suggested that you read this manual thoroughly to understand all the features and functions of your new amplifier. The purchase of a Fender amplifier will provide years of musical enjoyment and the `3206 helps keep the Fender legend going strong. WARNING: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE AMPLIFIER TO RAIN OR MOISTURE! `3206 FRONT PANEL FUNCTIONS A, B. UNDER NO CIRCUMSTANCES should a fuse of a different type, higher current rating, or a fuse bypass be used, as this could damage the equipment and present a serious safety hazard. This jack is wired in parallel with the MAIN SPEAKER JACK, and must only be used in conjunction with the MAIN SPEAKER JACK. Should the EXTERNAL SPEAKER JACK be used without also using the MAIN SPEAKER JACK, there will be no sound. GROUND SWITCH - The GROUND SWITCH is not functional, and is there to preserve the original appearance of the amplifier. speaker load, and that the speakers in the cabinet are wired for 4 ohms. Should a total load of more or less than 4 ohms be used, the amplifier will not put out its maximum power output before distortion occurs. This jack must always be used as the primary connection to speakers. C. POWER SWITCH - This switch turns the AC power ON and OFF. The footswitch allows you to turn the VIBRATO and REVERB features on and off without having to operate the controls on the front panel. D. STANDBY SWITCH - This switch turns the amplifier on and off. In the STANDBY position, the amplifier is off; however, power is applied to the tube filaments so as to eliminate warm-up time. Use of this feature during short breaks versus using the POWER SWITCH will increase tube life. NOTE: The VIBRATO and REVERB features will operate without plugging in the footswitch. LINE CORD Your amplifier is equipped with a grounding type supply cord to reduce the possibility of shock due to electrical fault. [. . . ] In the STANDBY position, the amplifier is off; however, power is applied to the tube filaments so as to eliminate warm-up time. Use of this feature during short breaks versus using the POWER SWITCH will increase tube life. NOTE: The VIBRATO and REVERB features will operate without plugging in the footswitch. LINE CORD Your amplifier is equipped with a grounding type supply cord to reduce the possibility of shock due to electrical fault. DO NOT ALTER THE AC PLUG. TOLEX COVERING CARE The exclusive Fender Tolex covering on your cabinet is of the same material that was used on the original VIBROVERB. A very light soapy solution on a sponge may be used to remove dirt and residue that may accumulate in the grain. [. . . ]