User manual FENDER 2224

[. . . ] W ishing you years of enjoyment and a heartfelt thank you, Bill Schultz Chairman Fender Musical Instruments Corporation SPECIFICATIONS TYPE: PART NUMBER: PR 329 MODEL GT 22-6300 (120V) 22-6330 (240V) Aust 22-6340 (230V)UK 22-6360 (230V) Eur 22-6370 (100V) 100V AC, 50/60 Hz 90W 120V AC, 60 Hz, 90W 230V AC, 50 Hz, 90W 240V AC, 50 Hz, 90W 25W into 8 at 5% THD Instrument: >500 k Tape/CD: 12 k Instrument: 100 mV Tape/CD: 120 mV for clipping One Fender Special Design 12" speaker (P/N 025923) 2 Button Footswitch, Controls Gain Select and Chorus (P/N 029972) Height: 17. 5 in Width: 17 in Depth: 9. 5 in 28 lbs 44 cm 43 cm 24 cm 12. 7 kg MODEL SE 22-6400 (120V) 22-6430 (240V) Aust 22-6440 (230V) UK 22-6460 (230V) Eur 22-6470 (100V) POWER REQUIREMENTS: POWER OUTPUT: INPUT IMPEDANCE : NOMINAL INPUT LEVEL: INPUT SENSITIVITY: SPEAKER: FOOTSWITCH: (Optional) DIMENSIONS: WEIGHT: Fender®, Tone-Master® and Princeton® Chorus are registered trademarks of FMIC. Product specifications are subject to change without notice. 7 TROUBLESHOOTING If the amp is set up but does not function, check the following items: COVERING CARE The exclusive covering on your Fender Automatic cabinet has been especially designed for years of lasting beauty. A very light soapy solution on a sponge may be used to remove dirt and residue that may accumulate in the fabric. [. . . ] REMEMBER TO UNPLUG THE POWER CORD BEFORE CLEANING AND WAIT UNTIL THE UNIT IS COMPLETELY DRY BEFORE PLUGGING IT IN. · · · · · Is the power cord properly plugged into an electrical outlet?Is the instrument properly plugged into the amplifier? (Eliminate any effects pedals and try using another cord. ) If after checking all of the above your amplifier is still not performing correctly, consult your authorized Fender Service Center. 6 YOUR 2224 AMPLIFIER Tape/CD Inputs - Play back accompaniment or learning tapes through your amp Footswitch Jack - On-Off Switching of the Chorus and Lead/Overdrive Channel Headphone Jack - For Private Listening Sensitivity Switch Automatically adjusts your amp's sensitivity for Single Coil or Humbucking Pickups 5 Preset Sounds - Created by the Fender ToneTeam, from Clean to Overdrive Congratulations on your purchase of a Fender Automatic series amplifier. Your new Fender amp is designed by the same Tone-Team that has created many other classic Fender amps: like the ToneMaster®, Princeton® Chorus and the versatile Hot Rod Series. Built with care and special attention to detail, your Automatic offers much more than meets the eye. Automatic Series Amplifiers include among their many features: 25 Watts of power; Classic Fender Reverb and 5 preset tone / gain buttons for everything from Fender clean to ultimate overdrive. Both the Automatic GT, voiced for rock and metal and the Automatic SE, voiced for blues and country, feature convenient front panel mounted controls and input jacks. The footswitch circuitry allows for remote selection of both the 5th preset (a lead or solo sound) and Chorus. Moreover, the Tape/CD input jacks and the 1/4 inch headphone jack make your Automatic the perfect amp for practice or small "single" gigs. Designed for the guitarist who wants a no nonsense approach to tone shaping and gain restructuring, your Automatic is a high quality Fender amplifier at an affordable price. TREBLE - Adjusts the amount of boost or cut in the high frequency range for all presets. BASS - Adjusts the amount of boost or cut in the low frequency range for all presets. L. CHORUS INDICATOR - This LED illuminates when the chorus circuit is active. CHORUS - This control automatically adjusts both the depth and sweep rate of the chorus circuitry. A lower setting produces a slow, full-range sweep whereas a higher setting produces a fast and less wide sweep. TAPE/CD INPUTS - Plug-in connection for any line level stereo or mono signal to be mixed together with the instrument signal. These inputs have fixed gain and are unaffected by any of the front panel controls. They can be used to connect a tape or CD player, or other signal source (rhythm machine, synth. . . ) to be used as accompaniment for practice or performance. The output level control of the external signal source is used to control its volume while the front panel VOLUME control is used for the instrument to obtain a balance. Q. [. . . ] FOOTSWITCH - Plug-in connection for the optional remote footswitch (P/N 029972) to select the lead/overdrive preset, and to switch the chorus on and off. For proper footswitch operation, both the LEAD/OVERDRIVE switch (item H) and the CHORUS switch (item O) must be in the `out' position. NOTE: Any good quality patch cord will work with the remote footswitch, however an unshielded speaker type cord is preferable to a coax guitar cord. [. . . ]