User manual FENDER 115XP
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual FENDER 115XP. We hope that this FENDER 115XP user guide will be useful to you.
Manual abstract: user guide FENDER 115XP
Detailed instructions for use are in the User's Guide.
[. . . ] XP ARTIST SERIES
LOUDSPEAKER SYSTEMS
110XP
112XP
115XP
1 1 0 X P, 1 1 2 X P, 1 1 5 X P
INSTRUCTION MANUAL
Fender®
XP Loudspeaker Systems
The Fender® 110XP, 112XP, and 115XP two-way, professional quality loudspeaker systems are designed to form the basis of everything from a public address system permanently installed, to the nightly rigors of a working band's portable sound system. Add ultra-deep bass to the your XP Series Loudspeaker System with a Fender 115sA or 118sA Subwoofer Loudspeaker System. [. . . ] Consider this when positioning speakers linked in a "daisy-chain. "
XP Series
Fender Pole Mount
Avoid damage to your equipment by 115sA/ ensuring that the total speaker 118sA impedance load is within the limits set by the amplifier's manufacturer. Listed below are the combined impedance loads of the XP Series loudspeaker connected in parallel with speakers of 4, 8 and 16 ratings: · XP Series 8 + any 4 speaker = 2. 6 load total · XP Series 8 + any 8 speaker = 4 load total · XP Series 8 + any 16 speaker = 5. 3 load total
www. f e n d e r . n e t
Acoustics and Cabinet Placement
There are several things to consider when placing loudspeaker cabinets. When used in a typical auditorium setting, position the speakers as shown in Fig. Ensure 70° adequate sound levels reach each seat in the audience by walking through the entire auditorium--listen for any gaps in coverage then reposition speakers as necessary. Recheck sound coverage with a full audience in attendance, if possible. When a XP speaker is placed near a wall, there will a low-fre70° quency boost of up to 3dB. The Audience drawback is that close proximity to a wall may also cause feedback. To avoid feedback: Increase the distance between speakers and the feedback source whether it is a wall, a microphone, or a guitar. Sound quality is often compromised when a sound system is required to be hidden from sight. [. . . ] n e t
a
g
e
1
4
0
XP Series Specifications
MODEL: 110XP 112XP 115XP
PART NUMBER:
071-1100-400
071-1200-400
071-1500-400
MAXIMUM OUTPUT: (at 1 Meter)
117dB Continuous 123dB Peak
118dB Continuous 124dB Peak
120 dB Continuous 126dB Peak
CABINET:
5/8" (1. 6 cm) Particle Board
5/8" (1. 6 cm) Particle Board
5/8" (1. 6 cm) Particle Board
CONNECTIONS:
(2) 1/4" Phone Jacks
(2) 1/4" Phone Jacks
(2) 1/4" Phone Jacks
DRIVER:
Low Frequency:
10" (25. 4 cm) woofer 2" (5. 1 cm) voice coil
12" (30. 5 cm) woofer 2" (5. 1 cm) voice coil Dual Piezoelectric Compression Drivers 1 1/2" (3. 8 cm) diaphragms
15" (38. 1 cm) woofer 2. 5" (6. 4 cm) voice coil Dual Piezoelectric Compression Drivers 1 1/2" (3. 8 cm) diaphragms
High Frequency:
Dual Piezoelectric Compression Drivers 1 1/2" (3. 8 cm) diaphragms
FREQUENCY RESPONSE:
65 Hz to 20kHz
60 Hz to 20kHz
60 Hz to 20kHz
SENSITIVITY:
1W/1m:
97 dB
98 dB
98 dB
POWER HANDLING:
100W (RS-426A) 200W (Program) 400W (Peak)
100W (RS-426A) 200W (Program) 400W (Peak)
150W (RS-426A) 300W (Program) 600W (Peak)
IMPEDANCE:
8
8
8
DIMENSIONS:
Height Width (front) Width (rear) Depth
20. 3" (51. 6 cm) 14. 6" (37. 1 cm) 6. 4" (16. 3 cm) 15. 6" (39. 6 cm)
21. 3" (54. 1 cm) 18" (45. 7 cm) 6. 4" (16. 3 cm) 18. 4" (46. 7 cm)
23. 9"(60. 7 cm) 21" (53. 3 cm) 8. 4" (21. 3 cm) 19. 6" (49. 8 cm)
WEIGHT:
37 lbs. CORONA, CA USA Fender® is registered trademark of FMIC Tolex® is a registered trademark of GenCorp, Inc.
P/N 057245
REV A [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FENDER 115XP
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual FENDER 115XP will begin.