User manual FENDER 110XP

[. . . ] XP ARTIST SERIES LOUDSPEAKER SYSTEMS 110XP 112XP 115XP 1 1 0 X P, 1 1 2 X P, 1 1 5 X P INSTRUCTION MANUAL Fender® XP Loudspeaker Systems The Fender® 110XP, 112XP, and 115XP two-way, professional quality loudspeaker systems are designed to form the basis of everything from a public address system permanently installed, to the nightly rigors of a working band's portable sound system. Add ultra-deep bass to the your XP Series Loudspeaker System with a Fender 115sA or 118sA Subwoofer Loudspeaker System. [. . . ] Consider this when positioning speakers linked in a "daisy-chain. " XP Series Fender Pole Mount Avoid damage to your equipment by 115sA/ ensuring that the total speaker 118sA impedance load is within the limits set by the amplifier's manufacturer. Listed below are the combined impedance loads of the XP Series loudspeaker connected in parallel with speakers of 4, 8 and 16 ratings: · XP Series 8 + any 4 speaker = 2. 6 load total · XP Series 8 + any 8 speaker = 4 load total · XP Series 8 + any 16 speaker = 5. 3 load total www. f e n d e r . n e t Acoustics and Cabinet Placement There are several things to consider when placing loudspeaker cabinets. When used in a typical auditorium setting, position the speakers as shown in Fig. Ensure 70° adequate sound levels reach each seat in the audience by walking through the entire auditorium--listen for any gaps in coverage then reposition speakers as necessary. Recheck sound coverage with a full audience in attendance, if possible. When a XP speaker is placed near a wall, there will a low-fre70° quency boost of up to 3dB. The Audience drawback is that close proximity to a wall may also cause feedback. To avoid feedback: Increase the distance between speakers and the feedback source whether it is a wall, a microphone, or a guitar. Sound quality is often compromised when a sound system is required to be hidden from sight. [. . . ] n e t a g e 1 4 0 XP Series Specifications MODEL: 110XP 112XP 115XP PART NUMBER: 071-1100-400 071-1200-400 071-1500-400 MAXIMUM OUTPUT: (at 1 Meter) 117dB Continuous 123dB Peak 118dB Continuous 124dB Peak 120 dB Continuous 126dB Peak CABINET: 5/8" (1. 6 cm) Particle Board 5/8" (1. 6 cm) Particle Board 5/8" (1. 6 cm) Particle Board CONNECTIONS: (2) 1/4" Phone Jacks (2) 1/4" Phone Jacks (2) 1/4" Phone Jacks DRIVER: Low Frequency: 10" (25. 4 cm) woofer 2" (5. 1 cm) voice coil 12" (30. 5 cm) woofer 2" (5. 1 cm) voice coil Dual Piezoelectric Compression Drivers 1 1/2" (3. 8 cm) diaphragms 15" (38. 1 cm) woofer 2. 5" (6. 4 cm) voice coil Dual Piezoelectric Compression Drivers 1 1/2" (3. 8 cm) diaphragms High Frequency: Dual Piezoelectric Compression Drivers 1 1/2" (3. 8 cm) diaphragms FREQUENCY RESPONSE: 65 Hz to 20kHz 60 Hz to 20kHz 60 Hz to 20kHz SENSITIVITY: 1W/1m: 97 dB 98 dB 98 dB POWER HANDLING: 100W (RS-426A) 200W (Program) 400W (Peak) 100W (RS-426A) 200W (Program) 400W (Peak) 150W (RS-426A) 300W (Program) 600W (Peak) IMPEDANCE: 8 8 8 DIMENSIONS: Height Width (front) Width (rear) Depth 20. 3" (51. 6 cm) 14. 6" (37. 1 cm) 6. 4" (16. 3 cm) 15. 6" (39. 6 cm) 21. 3" (54. 1 cm) 18" (45. 7 cm) 6. 4" (16. 3 cm) 18. 4" (46. 7 cm) 23. 9"(60. 7 cm) 21" (53. 3 cm) 8. 4" (21. 3 cm) 19. 6" (49. 8 cm) WEIGHT: 37 lbs. CORONA, CA USA Fender® is registered trademark of FMIC Tolex® is a registered trademark of GenCorp, Inc. P/N 057245 REV A [. . . ]