User manual FELLOWES PS60PS60CCPS70PS75PS80DMCDM4DM6 MANUAL-1999

[. . . ] (See Table A) · Depress the power switch to the ON (I) position to activate the standby mode. · Shredder automatically starts when paper is placed in the entry and stops when finished shredding. · If the machine is not properly seated on the basket, the red light will come on. A B C D E · Read and save these instructions. · Always turn off and unplug the machine before moving, cleaning, or conduct other than normal operation. [. . . ] · Folding paper to fit the entry increases the thickness and recommended capacity may be exceeded. · Clips and staples increase the thickness and may decrease sheet capacity. US 20# Paper Model: PS60 PS70 PS75 DM-4 DM-6 PS60CC PS80 DM-C Sheets per Pass 120V/50Hz 12 12 12 12 12 7 7 7 64 GSM Sheets per Pass 100V/50Hz 14 14 14 N/A N/A 9 9 N/A 80 GSM 230V/50Hz 12 12 12 N/A N/A 7 7 N/A 80 GSM 240V/50Hz 12 12 12 N/A N/A 7 7 N/A Installation · Assemble basket (and stand, if applicable). · Plug power cord into a standard AC outlet with the appropriate power requirements as stated on the serial number label adhered to the bottom of the shredder. Sheets per Pass Sheets per Pass All Models F TABLE A 2 Different paper weights and electrical currents will affect capacity. 3 Safety & Maintenance of PS60CC, PS80, DM-C The PS60CC, PS80, DM-C cross cut shredder creates small particles that, if allowed to accumulate, cause the shredder to jam. Follow these simple precautions to significantly reduce the likelihood that particles will accumulate and to keep your cross cut shredder operating at peak efficiency: · Do not allow the basket to overfill. The power of this shredder will compress paper particles into the basket even when it is full. The life of your shredder may be reduced if the cutting system continues to operate with particles packed around it. · Every second or third time you empty the basket; · If the shredder's cutting capacity is diminished; · If the cutting cylinders stop with a squeak or a rubbing sound after power is removed. Use Powershred Lubricant #35250 or a suitable alternative with an extension nozzle. Squeeze the lubricant across the full width of the cutters and then turn the machine on and run the cutting system forward for a few seconds. (Cross-cut machines with auto start: block the photo eye with a piece of paper in order to run the cutting system forward). Then, depress the reverse button and run the cutting system for a few seconds. Safety of PS60CC, PS80, DM-C · Do not operate PS60CC, PS80, DM-C without the basket it was shipped with. Indicator Lights (on select models) 1 2 A B C D E F 5 16 4 2 A B C PS60, 60CC, DM-C, DM-4, DM-6 3 5 D E Paper Jams 1. Depress power switch to the REVERSE (R) position until the jammed paper has been fully removed from the cutter. If the REVERSE (R) function will not operate when pressed, the internal overload protection device has been activated. Release the power switch from the REVERSE (R) POSITION, wait 15 seconds and repeat. In the machine jams in reverse, unplug the unit and cut all excess paper off the top and bottom of the machine before repeating the jam-clearing procedure. PS70, PS75, PS80 F All Models 4 Overload Protection This shredder is protected by a built-in thermal overload device that serves to protect the motor from overuse. [. . . ] ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any consequential or incidental damages attributable to this product. For more detail or to obtain service under this warranty, please contact Fellowes Customer Service at 1-800-955-0959, Monday through Friday, 8 AM - 5 PM (Central Standard Time). For specific instructions on obtaining service under this warranty on machines purchased outside the USA, contact the appropriate location listed in the Contact for Service section of this instruction manual. [. . . ]