User manual FELLOWES GALAXY E500

[. . . ] ("Fellowes") warrants the parts of the machine to be free of defects in material and workmanship and provides service and support for 3 years from the date of purchase by the original consumer. Fellowes warrants the cutting blades of the machine to be free from defects in material and workmanship for the lifetime of the shredder. [. . . ] If any part is found to be defective during the warranty period, your sole and exclusive remedy will be repair or replacement, at Fellowes' option and expense, of the defective part. This warranty does not apply in cases of abuse, mishandling, or unauthorized repair. ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any consequential or incidental damages attributable to this product. The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations, restrictions, or conditions may be required by local law. For more details or to obtain service under this warranty, please contact us or your dealer. Help Line Australia Canada +1-800-33-11-77 +1-800-665-4339 Europe Mexico United States 00-800-1810-1810 +1-800-234-1185 +1-800-955-0959 1789 Norwood Avenue, Itasca, Illinois 60143-1095 · USA· 630-893-1600 Australia Korea Benelux Poland Canada Russia China Singapore France South Africa Germany Spain Italy United Kingdom Japan United States 2010 Fellowes, Inc. 404032 SB-125i/SB-125Ci Please read these instructions before use. · Product is intended for commercial use only, and not for use around children. 15 15 15 BASIC SHREDDING OPERATION PAPER/CARD OR CD 1 2 AUTO 3 4 5 6 AUTO 7 7 Continuous operation: 45 minutes maximum NOTE: Continuous operation beyond 45 minutes will trigger 45 minute cool down period. Plug in and put disconnect Press ( ) ON to activate power switch in ON (I) position Feed paper/card straight into paper entry and release To shred CDs rotate CD flap into place Hold CD at edge, feed into CD entry and release When finished shredding set to OFF ( ) or Do nothing and shredder will go automatically to sleep mode 2 www. fellowes. com features an extensive on-line support section with a number of self-service options JAM PROOF SYSTEM OPERATION* Eliminates frustrating jams by preventing overloads and powering through misfed paper. 1 Advanced Jam Prevention- Electronically measures paper thickness to prevent paper jams: Up to RED: Too many sheets have been inserted. Up to GREEN: More sheets can be added. 2 3 Remove several sheets until indicator is below red. Continue 100% Jam Proof Shredding If a misfeed occurs: All indicators light up and shredder pauses for 3-6 seconds Wait for flashing to stop after automatic correction is complete. Regular shredding will resume. illuminates after paper has been If reversed, press reverse and remove paper. Otherwise, regular shredding will resume. *100% Jam Proof when used in accordance with user manual SLEEP MODE WHEN IN SLEEP MODE SAFESENSE® TECHNOLOGY OPERATION SET-UP AND TESTING 1 2 AUTO 3 1 AUTO 2 3 4 In sleep mode To get out of sleep mode or touch control panel insert paper Turn the shredder ON ( ) to activate SafeSense® Touch test area and look for the SafeSense® indicator to illuminate SafeSense® is active and working properly If hand is held on SafeSense® area more than 2 seconds shredder will shut off BASIC PRODUCT MAINTENANCE AND TROUBLESHOOTING OILING SHREDDER All cross-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive noise when shredding and could ultimately stop running. To avoid these problems, we recommend you oil your shredder each time you empty your waste bin. FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE CLEANING AUTO-START INFRARED SENSORS Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors may become blocked by paper dust causing the motor to run even if there is no paper present (Note: two paper detection sensors are located in the center of the paper entry). TO CLEAN THE SENSORS 1 AUTO 2 AUTO 3 AUTO 1 AUTO 2 AUTO 3 AUTO 4 *Apply oil across entry Shred one sheet Press and hold forward ( ) 2-3 seconds Turn off and unplug shredder Locate Auto-start infared sensor Dip cotton swab in rubbing alcohol *Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250 Using cotton swab, wipe away any contamination from the paper sensors PREvENTIvE MAINTENANCE AND MISCELLANEOUS TROUBLESHOOTING 15 · SelfCleaningCycle:Shredderperiodicallycyclesinforwardandreverselasting3-6seconds(SB-125Ci). · Emptywastebasketwhenbinfullindicatorlightsup. [. . . ] However, on rare occasions the sensors may become blocked by paper dust causing the motor to run even if there is no paper present (Note: two paper detection sensors are located in the center of the paper entry). TO CLEAN THE SENSORS 1 AUTO 2 AUTO 3 AUTO 1 AUTO 2 AUTO 3 AUTO 4 *Apply oil across entry Shred one sheet Press and hold forward ( ) 2-3 seconds Turn off and unplug shredder Locate Auto-start infared sensor Dip cotton swab in rubbing alcohol *Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250 Using cotton swab, wipe away any contamination from the paper sensors PREvENTIvE MAINTENANCE AND MISCELLANEOUS TROUBLESHOOTING 15 · SelfCleaningCycle:Shredderperiodicallycyclesinforwardandreverselasting3-6seconds(SB-125Ci). · Emptywastebasketwhenbinfullindicatorlightsup. · Maintenanceisanimportantpartofprotectingyourinvestment. Don'tforgetouroil(35250)andshredderbags(36054). [. . . ]