User manual FELLOWES 220-2220C-2C-220C-220C MANUAL-2005

[. . . ] · Avoid touching exposed blades on underside of confetti-cut shredder head. · Make sure the electrical rating listed on the serial label (near the power cord on the back of the shredder) matches the available electric power. · Secure shredder to wall with hardware provided in order to meet UL 60950 stability requirements. James Fellowes Chairman & CEO Contents Product Profile . . 8 While operating shredder · Keep hands and hanging objects (jewelry, ties, loose clothing, long hair, etc. ) away from paper entry. [. . . ] Use care when removing paper shreds. 2 Operation Control Switches I J K Control Switch (H) I F AUTOMATIC Turns on the automatic-start sensor and the green Ready light. Turbo Jam Release Button (F) Runs shredder when button is held down. 3 To clear a paper jam · If paper jam light (I) is on, follow these steps until light turns off. · Press and hold the reverse [R] button to back paper out of the paper entry (B). · Alternate between forward and reverse, as needed, until the jam clears: ­ Press and hold the manual forward button (F) for a few seconds. · Continue alternating between forward and reverse until the jam clears. Caution: The shredder may be damaged if you alternate too rapidly between forward and reverse. O OFF Turns off the automatic-start sensor and the green Ready light. Press and hold to activate. G H Troubleshooting Lights Ready Light (G) (Green) Shredder is in automatic start mode. Paper Jam (I) (Red) Shredder is jammed (e. g. , too much paper fed at one time). Basket Full [J] (Red) Waste basket is full or paper has collected under cutting cylinders. Door Ajar (K) (Red) Cabinet door is open. Maintenance Empty waste basket regularly to ensure the smooth functioning of the cutting cylinders. Oil confetti-cut model (220C-2/C-220C) regularly to ensure proper operation. If used at or near daily capacity, apply oil every time you empty the basket. Use Fellowes Powershred Lubricant #32250 or other non-aerosol vegetable-based oil in a long-nozzle container (sample oil provided). CAUTION: Do not use flammable synthetic oil, petroleum-based products, or aerosol lubricants of any kind. For convenience and energy savings, your shredder is equipped with an automatic-start sensor (O). This means that when the control switch (H) is in the automatic [I] position, the shredder will start running when you put paper into it and stop a few seconds after the paper has passed through. CAUTION: The automatic-start sensor cannot tell the difference between paper and other objects. Unplug the shredder if it will not be used for an extended period. To oil the cutting cylinders · Lift paper entry flap (N) and apply oil over full width of cutting cylinders through the paper entry (B). · Press and hold the Turbo Jam Release Button (F) for at least 3 seconds. · Press and hold the reverse [R] button for at least 3 seconds. · Store oil bottle in slot (L) inside cabinet door (A). To shred Press control switch (H) to automatic [I] position. [. . . ] 100V 50/60Hz 3. 9mm Confetti Cut 13 A4 70g. Door ajar light (K) is on Basket full light (J) is on Paper jam light (I) is on Confetti-cut shredder (220C-2/C-220C) Shredder sheet capacity decreases, noise level increases, or cutting cylinders stop with a squeak or rubbing sound Shredder runs for a few seconds after the paper has cleared the cutters Make sure the cabinet door (A) is closed. Follow the instructions under Maintenance. Warranty Fellowes, Inc. ("Fellowes") warrants the cutting cylinders of the machine to be free from defects in material and workmanship for 20 years from the date of purchase by the original consumer. Fellowes warrants all other parts of the machine to be free of defects in material and workmanship for 2 years from the date of purchase by the original consumer. [. . . ]