User manual FAYTECH 8 INCH TOUCH MONITOR

[. . . ] 144 250 500:1 10/15 140:120 12~36 4 <0, 5 -10~ +60 4-wire resistive 1xUSB port, 1xserial port Windows, Linux, Apple > 10 000 000 < 10 3H 20 ~ 150 2x Video (1x back cam view), 1x SVIDEO, 1x VGA, 1x HDMI 2x Audio-In, 1x earphone out 1x USB port 230V, 12V OSD-Menü, Lautsprecher, Fernbedienung, Touchstift Faytech touch displays are produced following the most modern production and test processes. carefully selected components and accurate production ensure reliable operation and long life. Faytech warrants to the original purchaser that each faytech touch display delivered shall be free from defects in material or workmanship at time of shipment, and that each such module delivered will meet the published specifications for a period of 24 months as measured from the date of original shipment. Faytech's obligation under the Warranty contained herein is limited to the repair or replacement of any faytech touch monitor that does not meet the specifications, provided that said product is returned to faytech, transportation charges pre-paid, and provided that upon faytech's examination, the product, when tested within the specified ratings and in accordance with good engineering practice, does not meet the specifications as defined. [. . . ] To switch back to a previous step, click the "<back" button. It's advisable to close all other programs before beginning this installation. Check the box (see the picture on the next page upper left) only if you want to install the PS/2-Driver. The PS/2-Driver works smoothly with a PS / 2 mouse but if you do not have a PS / 2 mouse you should leave this box unchecked to avoid compatibility problems. A calibration will be performed every time your PC starts up if you choose "Every system boot up". If you choose "Next system boot up" a calibration will be performed on the next system reboot. You can carry out a calibration at any time after the TouchKit program is installed. "Choose Destination Location": Accept the default destination or choose your own then press "Next". The installation will be started automatically with the selected settings. The installation is successfully completed when the following window appears: If the USB controller icon is not showing, please disconnect the USB cable from your PC and connect it again. (If you accepted all the defaults the program may be at "Start ­ Programs ­ Accessories ­ Touchkit ­ Configure Utility". General tab Gives information on whether one or more touch controllers are found and installed. After the initial installation, if no touch controller shows up on this tab, please pull out the USB connector on your PC and connect the device again. Enable Cursor Stablization: A software filter exists inside the driver to filter some noise to stabilize and smooth the touch points. This is a criterion to judge if the most recent touched point is the same as the previously touched point. If the difference between the two points is within this area, it will be recognized as the same touch point and the driver does not generate a new mouse event for this touch point. If the touch screen is touched and held for this period of time, the driver generates a right mouse click. You can adjust the faytech touch panel calibration with the functions called 4 Points Calibration, Clear and Calibrate, Linearization and Draw Test. By using the application drawing test, you can test the touch panel to determine if further setting changes are desirable. When you press the 4 Points Calibration button, the surface of the monitor shows the following image: Press blinking X symbol until stop blinking Touch and hold each of the blinking X symbols in the calibration window until it stops blinking to make sure that the utility can gather enough data for computation. In addition, a progress bar is shown at the bottom of the window to indicate time elapsed. If the touch screen is not touched before the progress bar gets to the far right, the calibration task will be terminated automatically. [. . . ] With an ATI graphic card, you can set up profiles in the advanced catalyst control center under profiles. Activate a hotkey, so that you can change the profiles of each display (one is the touch display, the other is the higher resolution display). Also you can configure the profiles using a software tool such as powerstrip. Power supply error: If the display has no signal input, there might be an error with the power supply. [. . . ]