User manual ESYSCO KT-22X0

[. . . ] NO. CT-302 KT-2200 SPECIFICATIONS REV. C PAGE 3 OF 14 DATE 2000. 02. 14 CONTECTS 1. OVERVIEW ------------------------------------------------------------ 4 2. SPECIFICATIONS ---------------------------------------------------- 4 4. [. . . ] RS-232-C Interface RS-232-C Host PC KT-22X0 Signal Direction Signal Name 9 Pin 9 Pin Host PC KT-22X0 TXD 3 2 >>>>> RXD 2 3 <<<<< RTS 7 7 >>>>> SG 5 5 DTR 4 4 >>>>> - 9 Pin female D-sub connector : KT-22X0 - Transmission Distance : Max. Baud Rates SW2 SW1 Baud Rate On On 9600 Off On 4800 On Off 2400 Off Off 1200 - Default : 9600 Baud Rate 4. 2. 2. Parity Settings SW4 SW3 Parity On Off Odd Parity Off Off Even Parity On On No Parity Off On No Parity - Default : Even Parity 4. 2. 3. Data Length Settings SW5 Data Bits On 8 Bits Off 7 Bits - Default : 7 Bits 4. 2. 4. Model Settings SW8 SW7 SW6 Model On On Off KT-2210 On Off On KT-2220 On Off Off KT-2230 Off On Off KT-2250 Off Off On KT-2260 Off Off Off KT-2280 - These settings should not be changed by the user ESYSCO AG www. esysco. com ESYSCO AG S e n n w e i d s t ra s s e 4 5 CH-6312 Steinhausen Tel. NO. CT-302 KT-2200 SPECIFICATIONS REV. C PAGE 6 OF 14 DATE 2000. 02. 14 5. Mode Control The reader operates in two basic modes, READY MODE and HOST CONTROLLED MODE. Upon applying power to the reader, LEDs are lit for 250m secs, and buzzer beeps for 250m secs. READY MODE When power is first applied, the reader defaults to this mode, in which it arms itself to read. When a card is swiped readers send the data ( no start / end sentinel or LRC ) preceded by a track identifier and followed by CR. The Card Reader transmit the lower track first, which is Track I , Track II, Track III . Single Track Reader Result Buzzer (msec) Good 250 Error ERROR BEEP Green LED (msec) 250 Red LED (msec) 800 Dual or Triple Track Reader Result Buzzer (msec) Green LED (msec) T1 OR T2 OR T3 Good 250 250 ALL Track error ERROR BEEP * ERROR BEEP : On Off On Off On 200 100 200 100 200 (msec) Red LED (msec) 800 After terminating the transmission and the LED and buzzer indications, the reader rearms itself to read. " ( 3Fh ) : " ^ " ( 5Eh ) ESYSCO AG www. esysco. com ESYSCO AG S e n n w e i d s t ra s s e 4 5 CH-6312 Steinhausen Tel. NO. CT-302 KT-2200 SPECIFICATIONS REV. C PAGE 7 OF 14 DATE 2000. 02. 14 5. 2. 2. HOST CONTROLLED MODE Upon receiving the Clear and Initialize command (C), the reader goes to this mode, where all actions are controlled by the host commands. Command and response format : <STX> command (response) <ETX><BCC> Commands and responses: Code Definition A ( 41h ) Arm to read (but do not transmit status report) B ( 42h ) Arm to read and send status report after swipe (good or bad swipe) C ( 43h ) Clear and lnitialize D ( 44h ) Turn buzzer on for 250 msec E ( 45h ) Turn buzzer on for 200 msec 3times F ( 46h ) Turn green LED on for 250 msec G ( 47h ) Turn red LED on for 800 msec H ( 48h ) Turn green LED and buzzer on for 250msec I ( 49h ) Turn Red LED and buzzer on for 800msec J ( 4Ah ) Transmit Track I data K ( 4Bh ) Transmit Track II data L ( 4Ch ) Transmit Track III data M ( 4Dh ) Status request N ( 4Eh ) Return to READY MODE ' ( 60h ) Status report befor swipe a ( 61h ) Status report - data for track 1 b ( 62h ) Status report - data for track 2 c ( 63h ) Status report - data for track 1&2 d ( 64h ) Status report - data for track 3 e ( 65h ) Status report - data for track 1&3 f ( 66h ) Status report - data for track 2&3 g ( 67h ) Status report - data for track 1&2&3 * ( 2Ah ) Error message ( No start sentinel / No end sentinel / Parity error / LRC error ) STX ( 02h ) Start of text ETX ( 03h ) End of text EOT ( 04h ) End of transmission ACK ( 06h ) Acknowledgment NAK ( 15h ) Negative ACK Direction <---- host <---- host <---- host <---- host <---- host <---- host <---- host <---- host <---- host <---- host <---- host <---- host <---- host <---- host ----> host ----> host ----> host ----> host ----> host ----> host ----> host ----> host ----> host <---> host <---> host <---> host <---> host <---> host ESYSCO AG www. esysco. com ESYSCO AG S e n n w e i d s t ra s s e 4 5 CH-6312 Steinhausen Tel. [. . . ] Control LED and BUZZER Host KT-22X0 <STX>D<ETX><BCC> or <STX>E<ETX><BCC> ----------> <---------- <STX><EOT><ETX><BCC> ( Turn buzzer on for 250 or 200msec 3 times ) <STX>F<ETX><BCC> or <STX>G<ETX><BCC> ----------> <---------- <STX><EOT><ETX><BCC> ( Turn green/red LED on for 250 or 800msec) ESYSCO AG www. esysco. com ESYSCO AG S e n n w e i d s t ra s s e 4 5 CH-6312 Steinhausen Tel. Return to READY Mode KT-2200 SPECIFICATIONS REV. C PAGE 11 OF 14 DATE 2000. 02. 14 Host KT-22X0 ( Host Controlled Mode ) <STX>N<ETX><BCC> ----------> <---------- <STX><EOT><ETX><BCC> ( Ready Mode ) 6. 5. Status Report Host KT-22X0 <STX>A<ETX><BCC> ----------> <---------- <STX><ACK><ETX><BCC> <STX>M<ETX><BCC> ----------> <---------- <STX>'<ETX><BCC> ( Card Swipe ) <STX>M<ETX><BCC> ----------> <---------- <STX>c<ETX><BCC> or ( Track I, II ) <STX>f<ETX><BCC> or ( Track II, III ) <STX>e<ETX><BCC> or ( Track I, III ) <STX>g<ETX><BCC> ( Track I, II, III ) <STX>J<ETX><BCC> ----------> <---------- <STX><Track #1 Data><ETX><BCC> <STX><ACK><ETX><BCC> ----------> <STX>M<ETX><BCC> ----------> <---------- <STX>f<ETX><BCC> <STX>K<ETX><BCC> ----------> <---------- <STX><Track #2 Data><ETX><BCC> <STX><ACK><ETX><BCC> ----------> <STX>M<ETX><BCC> ----------> <---------- <STX>d<ETX><BCC> <STX>L<ETX><BCC> ----------> <---------- <STX><Track #3 Data><ETX><BCC> <STX><ACK><ETX><BCC> ----------> ESYSCO AG www. esysco. com ESYSCO AG S e n n w e i d s t ra s s e 4 5 CH-6312 Steinhausen Tel. [. . . ]