User manual ESET NOD32 ANTIVIRUS POUR NOVELL NETWARE

[. . . ] Certain names of program products and company names used in this document might be registered trademarks or trademarks owned by other entities. Microsoft and Windows are registered trademarks of Microsoft Corporation. Eset, spol. Svoradova 1, 811 03 Bratislava, Slovak Republic http://www. eset. sk/en Technical Support Worldwide: http://www. eset. com/support Technical Support for Europe: http://www. eset. eu/support REV. 20071116-002 ESET NOD32 Antivirus for Novell Netware Server 1. Introduction This User Guide describes the usage of ESET NOD32 Antivirus for Novell Netware Server (or just ESET NOD32 Antivirus for Novell), namely: ­ installation of the product, ­ configuration of individual modules, ­ updating of the product. [. . . ] To configure the mirror correctly, run this command on the console to set up and launch the NOD32UP2. NLM module: LOAD SYS:/NOD/NODUP. NLM SYS:/PUBLIC/MIRROR/ -update -period=60 Now ESET NOD32 Antivirus for Novell will be updated from the mirror directory SYS:/PUBLIC/MIRROR every hour (parameter -period=60). It is recommended to enable automatic startup of AMON. NLM and NOD32UP2. NLM at each server startup using system file AUTOEXEC. NCF. 3. Modules AMON. NLM To load AMON, use the following command on the system console: LOAD SYS:/NOD/AMON To unload AMON from memory, use the following command: UNLOAD AMON Quick guide through the complete installation Extract the installation package. Also, it is recommended to create file AMON. CFG ESET NOD32 Antivirus for Novell Netware Server AMON. CFG If there is present the file AMON. CFG in the directory with the module AMON. NLM, configuration from AMON. Syntax of the file AMON. CFG is as follows (each line may contain one of the following switches one switch per line): onread+ (default setting) Files will be tested in a moment when a command to open/read is detected. The opposite switch is: onreadonwrite+ (default setting) Files are tested at the moment when a command to create/modify is detected. The opposite switch is: onwriteonrename+ (default setting) Files are tested at the moment when a command to rename is detected. The opposite switch is: onrenameall (default setting) All files are tested. Otherwise, if the parameter allis used, only extensions defined by the Eset Company are tested. notify When an infiltration is detected, AMON sends a message to the user who attempted to access the infected file (using the NetWare Message PopUp Service). When an infiltration is detected, AMON sends a message to all users in the list. It is possible to list more users ­ in this case, use commas to delimit them ­ see the example above. Other parameters: pattern log logappend logrewrite clean rename delete heur heursafe heurstd heurdeep These switches are identical to those used in module NOD32. NLM. They are described below (when entering parameters, always omit the hyphen). NOD32. NLM To run the NOD32 diagnostic scan or clean, enter the command as follows: LOAD SYS:/NOD/NOD [parameters] [path list] If [path list] is not entered, NOD32 will automatically scan whole disk. The opposite switch is: -subdir-pack+ Enables testing of internally compressed files. The opposite switch is: -pack- (default setting) -arch+ Enables testing of archives (ZIP, RAR, ARJ. . . ). [. . . ] This folder will provide update files for the modules NOD32. NLM and AMON. NLM. [directory_with_NLM_modules] is optional in case the file NOD32UP2. NLM is located in the directory together with files NOD32. NLM and AMON. NLM. Possible parameters: -update Provides NOD32 updates (otherwise, available updates will be displayed only). -show_retvals Use of this parameter returns all possible return values with brief comments. [. . . ]