User manual ESCALADE SPORTS G0710

[. . . ] Call us at: 1-800-426-1421 (THIS IS A CONSUMER ONLY NUMBER) FAX: 812-467-1399 OR WRITE TO: ESCALADE SPORTS CUSTOMER SERVICE DEPARTMENT P. O. BOX 889 EVANSVILLE, IN 47706 When contacting Escalade Sports please provide model number, serial number (if applicable), and part number if requesting a replacement part. These numbers can be found on the product, packaging, and in this Owner's Manual. 1 REQUIRED TOOLS PHILLIPS SCREWDRIVER HAMMER 2 WRENCHES, INCLUDED WITH TABLE 2 0710-PR1 PARTS IDENTIFIER HARDWARE (ACTUAL SIZE MAY VARY) QTY. REQUIRED DESCRIPTION (EXTRA PIECES MAY BE INLCUDED) H1 BOLT 16 H2 BOLT 20 H3 FLAT HEAD PHILLIPS SCREW 40 H4 LONG ROUND HEAD PHILLIPS SCREW 5 H5 SHORT ROUND HEAD PHILLIPS SCREW 40 H6 BRACKET (not actual size) 3 4 PARTS IDENTIFIER HARDWARE (ACTUAL SIZE MAY VARY) QTY. [. . . ] LAY APRON SIDE PANELS P7A AND P7B ON A FLAT SURFACE WITH WOODGRAIN SIDE DOWN AND SCREW HOLES AT BOTTOM OF PANELS. THERE WILL BE A GROOVE RUNNING DIAGONALLY FROM LEFT TO RIGHT ON EACH PANEL. ATTACH AN APRON CORNER P10 TO THE END OF EACH APRON SIDE PANEL P7A AND P7B USING PHILLIPS HEAD SCREWS H5 WHERE THE GROOVE IS CLOSEST TO THE SCREW HOLES IN THE APRON SIDE PANEL P7A AND P7B . NOTE: THE APRON CORNER P10 CAN BE INSTALLED WITH EITHER END UP. H5 P10 P7A P10 H5 SCREW HOLES P7B SCREW HOLES 12 0710-PR1 ASSEMBLY INSTRUCTIONS POOL TABLE ASSEMBLY WARNING: TWO ADULTS NEEDED TO ASSEMBLE POOL TABLE 11. POSITION APRON SIDE PANELS P7A AND P7B AS SHOWN AND ATTACH TO PLAYING SURFACE P1G USING PHILLIPS FLAT HEAD SCREWS H3. BOARD IS POSITIONED CORRECTLY WHEN APRON CORNER P10 RESTS INSIDE CORNER CAPATTACHED TO MAIN ASSEMBLY P1. SLIDE THE APRON END PANEL P8 INTO EACH APRON CORNER P10 AND FASTEN USING PHILLIPS HEAD SCREWS H5 AND TO THE PLAYING SURFACE P1G USING FLAT HEAD PHILLIPS SCREWS H3. SLIDE LONG RETURN BOARD P6A INTO THE GROOVES OF THE APRON SIDE PANELS P7A AND LONG RAIL P1A. REPEAT ON OTHER SIDE BY SLIDING LONG RETURN BOARD P6B INTO THE GROOVES OF THE APRON SIDE PANELS P7B AND LONG RAIL P1B. NOTE: RUBBERIZED SIDES OF THE LONG RETURN BOARDS P6A AND P6B SHOULD FACE TOWARDS THE MAIN ASSEMBLY P1. (UPWARDS WITH TABLE UPRIGHTED) WITH ANGLED CORNERS TOWARDS APRON CORNERS P10. P10 P7A P8 P1B P10 P6A P1A P1G P6B P1B 13 P7B ASSEMBLY INSTRUCTIONS POOL TABLE ASSEMBLY WARNING: TWO ADULTS NEEDED TO ASSEMBLE POOL TABLE 14. ATTACH AN APRON CORNER P10 TO EACH END OF THE APRON BALL RETURN PANEL P9 USING PHILLIPS HEAD SCREWS H5. NOTE: POSITION APRON CORNERS P10 SO THE SCREW HOLE IS NOT IN LINE WITH GROOVE FOR APRON BALL RETURN PANEL P9. ATTACH THE ASSEMBLED APRON BALL RETURN PANEL P9 TO BOTH APRON SIDE PANELS P7A AND P7B USING PHILLIPS HEAD SCREWS H5 AND ATTACH TO PLAYING SURFACE P1A USING PHILLIPS FLAT HEAD SCREWS H3. MAKE SURE APRON BALL RETURN PANEL "GROOVE" IS AWAY FROM PLAYING SURFACE (DOWN IF TABLE IS UPRIGHTED). NOTE: A TOTAL OF THREE SCREWS WILL BE PUT IN APRON CORNERS P10 AT THIS END OF TABLE - ONE YOU WILL NOT BE ABLE TO REACH BECAUSE OF CORNER CAP. P7A H5 H3 P7B P9 P10 14 0710-PR1 ASSEMBLY INSTRUCTIONS POOL TABLE ASSEMBLY WARNING: TWO ADULTS NEEDED TO ASSEMBLE POOL TABLE 16. BEND SHORT RETURN BOARD P11 BY HAND AND INSERT INTO THE GROVES OF BOTH APRON SIDE PANELS P7A AND P7B BY SLIDING IN X DIRECTION. SLIDE IN THE Y DIRECTION INTO THE GROOVES OF THE APRON BALL RETURN PANEL P9. POSITION THE METAL BRACKETS H6 AS SHOWN AND TAP DOWN INTO PLACE WITH A HAMMER. AFTER THE GLUE HAS DRIED AND IS SET (APPROXIMATELY 12 HOURS), TURN THE TABLE ASSEMBLY OVER TO RIGHT SIDE UP. PLACE A POOL BALL ON THE PLAYING SURFACE AND LEVEL THE TABLE BY TURNING THE LEG LEVELERS P5. P5 P7A P11 H6 X Y X P7B P9 15 GAME RULES BILLIARDS Billiards refers to games played on a rectangular table covered with felt; pool is the most popular billiards game in the United States. Billiards games may be played by two players, teams of two players each, or three players. [. . . ] The object of the game is to pocket your opponent's balls. 16 0710-PR1 90 DAY WARRANTY Manufacturer warrants to the original retail purchaser, this product to be free from defects in material and workmanship for a period of ninety (90) days from the date of purchase. Should this product become defective due to material or workmanship within the warranty period, contact our Customer Service Department. This warranty is not transferable and does not cover normal wear and tear, or damage caused by improper handling, installation or use of this product. This warranty is also void if product is in any way abused, damaged, or modified from its original state, or if used for other than indoor residential use. [. . . ]