User manual EPSON STYLUS D120 START HERE

[. . . ] Also, make sure the total ampere rating of all devices plugged into the wall outlet does not exceed the wall outlet's ampere rating. Do not block or cover the openings in this product's cabinet. Warning, Cautions, and Notes w c Warnings must be followed carefully to avoid bodily injury. Cautions must be observed to avoid damage to your equipment. Notes contain important information and useful tips on the operation of your printer. When choosing a place for this product Place this product on a flat, stable surface that is larger than this product. This product will not operate properly if it is tilted or at an angle. When using this product Do not put your hand inside this product or touch the ink cartridges during printing. 15 cm or more 40 cm or more Do not move the print head by hand; otherwise you may damage this product. [. . . ] #1 #2 #3 #4 #5 #6 #7 #8 EPSON Stylus Pro 4800 Matte Black or Photo Black Cyan Magenta Yellow Light Black Light Cyan Light Magenta Light Light Black EPSON Stylus Pro 4400 Matte Black Cyan Magenta Yellow - 6 Loading Roll Paper Attaching the roll paper to the spindle When installing the roll paper onto the spindle, follow the steps below. After inserting all ink cartridges in their corresponding slot, lower the ink levers. When attaching roll paper with a 3-inch core, keep the gray attachments attached. When attaching the roll paper with a 2-inch core, remove the gray attachments from the flange. 8. After approximately two minutes, ink lever messages appear on the LCD. Raise or lower the ink levers accordingly until READY appears on the LCD, which indicates initial ink charging is completed. c Caution: Never perform the following tasks while the Pause light is flashing; otherwise, damage may occur. Unplug the power cord. Note: Keep the gray attachments in a safe place for future use. Slide the roll paper onto the spindle and onto the flange until it fixes into place. Note: Do not stand the spindle when attaching the roll paper. Hold the ink cartridge with the arrow mark facing up and pointing to the rear of the printer, and then insert it in the slot. 9. Note: If you have installed 220 ml ink cartridges, do not close the ink compartment cover(s). 4. Slide the movable flange (removed in step 1) onto the spindle and into the end of the roll paper until it fixes into place. 4. Fan a stack of paper, and then tap it on a flat surface to even the edges. If it curls excessively and jams frequently, stop using it. Premium Semigloss Photo Paper A4 LTR A3 Super A3/B 6. Dust may decrease the printout quality. Premium Luster Photo Paper LTR A3 Super A3/B 100 50 50 Photo Quality Ink Jet Paper EPSON Proofing Paper Semimatte (Commercial) A4 LTR Super A3/B 200 200 50 10 A3 Super A3/B Watercolor Paper-Radiant White Bright White Inkjet Paper Super A3/B 50 50 Note: You can load one sheet at a time into the rear feed slot. Paper with a thickness between 0. 08 and 1. 6 mm can be set in the landscape position. Plug the other end of the cable into the USB interface connector of the computer. After connecting the printer and the computer with the USB cable, see "Installing the Printer Software" on page 14. Using the built-in IEEE1394 interface To connect your printer and computer using the installed IEEE 1394 interface card, follow the steps below. Note: Be sure to use the IEEE 1394 Cable (C836302); otherwise, the cable may exceed the limit of the EMC Regulation of each country. Make sure both the printer and the computer are turned off. 12 2. Make sure the power cord is unplugged from the wall outlet. c Caution: Do not install the interface card when the printer is connected to a wall outlet. Use a cross-head screw driver to remove the two screws that secures the shield plate to the optional interface slot, and then lift off the plate. Be sure to keep the screws for future use when you re-install the shield plate. IEEE 1394 interface connector 3. [. . . ] Insert the Printer Software CD-ROM shipped with your printer in the CD-ROM drive. 14 For Mac OS X c Caution: Turn off all virus protection programs before you install the printer software. 5. Close the Printer List dialog box. Note: This software does not support the UNIX File System (UFS) for Mac OS X. Install the software on a disk or in a partition that does not use UFS. Insert the Printer Software CD-ROM shipped with your printer in the CD-ROM drive. [. . . ]