User manual EPSON EXPRESSION HOME XP-402

[. . . ] Read the license agreement, then click Agree. STOP: Be sure to install your scanner software first BEFORE you connect the scanner!See your Start Here sheet for details. Scanner CD-ROM with EPSON® Scan driver and electronic manual Power cord USB cable Click Agree 2 Slide the transportation lock to the UNLOCK position. Unless your scanner is connected in the middle of a SCSI chain, leave the terminator switch on the back of the scanner turned ON. Squeeze the lock releases on your SCSI cable, and plug the cable into either SCSI connector on the back of the scanner. Connect the pin end of the cable to the SCSI port on your computer. 2 5 Remove all the packing tape, but leave the two yellow stickers in place until instructed to remove them. IMPORTANT! When the Software Installation screen appears, click Install. Leave the stickers in place until you are instructed to remove them. STOP: Be sure to install your scanner software first BEFORE you connect the scanner! [. . . ] On-screen Help for EPSON Scan An error message says the selected area is too large for this resolution. If you're importing your image into a TWAINcompliant application like Photoshop, make sure you select EPSON Expression 1680 as your import source. 4 Click the Scan button. 8 9 Click the button to optimize your image's exposure. Click the Scan button, then click OK on the File Save Settings window. Close any programs you don't need. Also, try scanning at a lower resolution, or select part of the image to scan. If you're running Mac OS 8. 6 to 9. x, increase the memory of your host application. Scanning With Photoshop Click here Click the Help button or question mark that appears on the screen when you're using EPSON Scan. EPSON Technical Support The printed image doesn't look the same as the original. If the scanner glass is smudged or dusty, turn the scanner off and unplug the power cord. If your original document is dirty or wrinkled, it will show up in your scan. If the document is not aligned correctly (see "Your First Scan"), straight lines may come out jagged, or your printed image may look crooked. Try printing a test page to make sure your printer is operating correctly. Because your monitor and printer use different color technologies, your printed colors can't match the colors on your screen exactly. You can also import your scanned image into Adobe® Photoshop® Photoshop , Elements, or another TWAIN-compliant application. You can use the tools in these applications to modify the image before you save or print it. EPSON provides technical assistance 24 hours a day through the electronic support services and automated telephone services described below: You see the File Save Settings window. 1 2 Place your photo face down on the scanner glass. Note: If you don't like the preview, you can use EPSON Scan to fine-tune the image before scanning. · · World Wide Web From the Internet, you can reach EPSON Support at http://support. epson. com. Remove the CD-ROM. 3 4 9 6 USB cable IEEE 1394 FireWire® interface cable (Professional FireWire model only) 5 6 Gently close the transparency unit. Connect the transparency unit cable to the OPTION connector at the back of the scanner and tighten the screws. 10 2 Remove all the packing tape, but leave the two yellow stickers in place until instructed to remove them. 7 8 11 12 IMPORTANT! Leave the stickers in place until you are instructed to remove them. STOP: Be sure to install your scanner software first BEFORE you connect the scanner!See your Start Here sheet for details. Install LaserSoft SilverFast, MonacoEZcolor, and the ArcSoft Software Suite following the instructions included with each program. Then continue with the instructions under "Install the Transparency Unit. " Install LaserSoft SilverFast, MonacoEZcolor, and the ArcSoft Software Suite, following the instructions included with each program. Then continue with the instructions under "Install the Transparency Unit. " Note: LaserSoft SilverFast requires Mac OS 9. 2 or later. Turn over 4 Connect the Scanner After your transparency unit is installed, it's time to get connected. Getting the Most From Your Scanner The following sections contain overviews of how to get the most out of your professional scanner and its software. For detailed instructions, see the electronic or printed manuals for each software application. The SilverFast CD-ROM also contains useful QuickTime® tutorials. Scanning Film Note: To scan slides or medium- or large-format film, follow these steps but use the correct holder. See the User's Guide for details. More Scanning Options Here are more ways to get the most out of your scanner and software: 1 Slide the transportation lock to the UNLOCK position to unlock the scanner carriage. Connect the scanner to your computer using either the USB or FireWire cable that came with your scanner, or a SCSI cable. Note: Only the Professional FireWire model comes with a FireWire cable. 1 2 If necessary, remove the white document mat from the transparency unit. Locate the 35 mm film holder that came with your scanner and carefully pop the film cover off one of the strip holders. [. . . ] In Canada, please call (800) 463-7766 for dealer referral. SM 6 For the Scanner -> Internal setting, select Image Colour Matching (ICM) in Windows or ColorSync in Macintosh. For the Internal -> Output setting, select RGB. Problems? First, check the lights on the scanner. 7 For the Scanner (Reflective) or Scanner (Transparency) settings, select the Monaco scanner profiles you created. For the Internal setting, select Adobe RGB (1998). Scanning 48-bit Images For images in full 48-bit color depth, you can scan into ArcSoft PhotoStudio® with EPSON Scan. You can also scan an image with the standalone SilverFast application. READY READY ERROR Flashing green Warming up or scanning. [. . . ]