User manual EPSON EMP-5300 annexe 1

[. . . ] (Warm-up in progress) 4 Power 5 Turn on the power for the input source. In the case of a VCR, press the PLAY button. 2 3 Tip If a laptop computer or a computer with a LCD screen has been connected to the projector, you may need to change the output destination for image signals depending on the computer keys ( The , and other displays are situated on the computer keys) or the computer's settings. The output destination can normally be changed by holding down the computer's and pressing one of the Function keys. Once the source has been changed, after a short wait the projector will start projecting. [. . . ] For details, refer to the documentation provided with your computer. If images do not appear . . . Press the button that corresponds to the port into which the image device is connected to change the input signal. 4 Projector Remote Control If you have other problems . . . Refer to the online Help information. Help Help Examples of changing output NEC Panasonic TOSHIBA IBM SONY FUJITSU Macintosh After restarting the computer, change the Control Panel monitor and sound settings so that Mirroring is active. Help Help Press the or and then follow the instructions. Projector Remote Control * Refer to Troubleshooting. Projecting Adjustment Pages 37-40 of Owner's Manual Adjusting the projection angle Lift the front of the projector while pulling up the foot adjust lever, adjust the amount extension or retraction of the front foot, then adjust the projector's projection angle. 5 Tip If you change the projection angle, you may get keystone distortion in the Keystone To make fine adjustments: Becomes lower images. You can use the on the projector's control panel to correct keystone distortion. See page 7. To store the extended front feet, pull up the foot adjust lever and then slowly lower the front panel. Becomes higher Adjusting the image size and focus Projection position adjustment (up/down) Image size adjustment Focus adjustment Automatically adjusting computer images to the optimum settings Press on the operation panel or open the cover on the remote control and press automatically adjust the tracking, the display position and the synchronization. to 6 Projector Remote Control Other adjustments Press on the operation panel or open the cover on the remote control and press to display the setting menu on the projection screen. Then adjust the required settings, such as brightness, contrast and sharpness. Using the on-screen menus Menu screen Projector panel operations Move up Return Move left Remote control Select /Execute Move up Move left Move right Move right Select/Execute Move down Move down Return Projector Remote Control Adjustment / Turning Off the Projector Adjustment Correcting keystone distortion Page 38 of Owner's Manual If the images have keystone distortion . . . Keystone Press on the projector's control panel to correct the keystone distortion. 7 Tip When keystone correction is carried out, the projected image will become smaller. If the images become uneven in appearance after keystone correction is carried out, decrease the Sharpness setting. Keystone Projector When the top area is spread open. Keystone When the bottom area is spread open. Keystone Turning Off the Projector Page 35 of Owner's Manual 1 Turn off the power for the equipment connected to the projector. Power 8 2 Press the Power twice to turn off the projector's power. Press once to display the confirmation message in order to prevent miss-operations. Power Press it once more to switch off the power supply. It is possible to switch off the power supply by pressing The twice consecutively. will start flashing orange. (Cool-down in progress) 3 Check that the is lit steadily with an orange color, and then disconnect the power cord. If the power cord is disconnected while the is still flashing orange, it may cause problems with projector operation. * Set the R/C switch on the remote control to the OFF position. (Operation Indicator) Adjustment / Turning Off the Projector Functions for Enhancing Projection Wireless mouse Effect E-Zoom A/V Mute This projector is equipped with a variety of useful functions for enhancing projection. Then select the type of screen to be displayed when projection is being stopped. The default setting is the black screen. Functions for Enhancing Projection Troubleshooting Page 42 of Owner's Manual Viewing the online help This projector is provided with an online help function which can be used when you have a problem using the projector. Help Help Help Help 13 1 Press or . 2 Select the item to view. Press the on the projector's control panel. Or tilt the on the remote control. Projector (HELP Menu) Help for the image Help for the sound Language selection(Language) If you follow the instructions to solve the problem unsuccessfully, unplug the power from the wall outlet and contact with your local dealer. Remote Control 3 Accept the selected item. Press the on the projector's control panel. Or press the on the remote control. :Select :Enter :Exit (HELP Menu) An image does not appear on the Screen. (cut off/too big/too small/partial) The colors of the image are not correct. :Select :Enter :Return :Exit 4 The selected item will appear on the screen. Checking the indicators Page 70 of Owner's Manual The projector is equipped with indicators that alert you to problems with projector operation. The following tables show what the indicators mean and how to remedy problems that they indicate. 14 Lamp Indicator Indicator status Problem and remedy Lamp error. *2 The power has not been switched on or normal projection is in progress. Operation indicator Lamp indicator Temperature indicator Blinking in Red Blinking in Orange Extinguished Operation Indicator Indicator status Illuminated in Orange Temperature Indicator Problem and remedy Indicator status Problem and remedy Excessive internal temperature (overheating). [. . . ] *2 The power has not been switched on or normal projection is in progress. Operation indicator Lamp indicator Temperature indicator Blinking in Red Blinking in Orange Extinguished Operation Indicator Indicator status Illuminated in Orange Temperature Indicator Problem and remedy Indicator status Problem and remedy Excessive internal temperature (overheating). After re-inserting it, press the and turn on the power again. Power Standby condition. Projection will start a few moments after has been pressed. Power Illuminated in Red Blinking in Orange Illuminated in Green Blinking in Green Blinking in Red Extinguished Cool-down in progress. [. . . ]