User manual EPSON C82435*

[. . . ] Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation. EPSON and EPSON ESC/P are registered trademarks and EPSON StylusTM is a trademark of Seiko Epson Corporation. Apple, Macintosh, AppleShare, LaserWriter, AppleTalk, LocalTalk, EtherTalk, OpenTransport, Kanji-Talk, and Rendezvous are registered trademarks of Apple Computer, Inc. Unix is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Limited. [. . . ] NET USE printer port: \\NetBIOS name of print server\Device name of print server Selecting the port 1. Click the Ports tab and then select the port you have set using the NET USE command. Chapter 5 Installing the Printer Driver 132 Windows NT 4. 0 For Windows NT 4. 0, the printer driver installation procedure differs depending on the printing method you prefer. LPR printing Note: If you are using EpsonNet Direct Print, the setup procedure is different. Select LPR Port from the Available Printer Port list, and then click New Port. Note: You cannot use the Lexmark TCP/IP Network Port with this print server. Enter the IP address of the print server in the first text box and the printer name in the second text box. In the Printer Ports dialog box, click Close. Chapter 5 Installing the Printer Driver 133 8. See "Installing a printer driver" on page 135 to install the printer driver. Internet printing Internet printing is possible by using the EpsonNet Internet Print utility included on the Software CD-ROM. See "About EpsonNet Internet Print" on page 196 for more details. Microsoft Network Shared printing 1. Select the printer you want to configure from the Shared Printers list. If you cannot select the printer, enter the following in the Printer box: \\NetBIOS name of print server\Device name of print server 5. See "Installing a printer driver" on page 135 if necessary. Chapter 5 Installing the Printer Driver 134 Installing a printer driver 1. From the Output Port list box, select one from \PIPE\LPD0 to \PIPE\LPDn (where n is the maximum number of LPD ports). The \PIPE\LPD -Settings dialog box will appear. Chapter 5 Installing the Printer Driver 142 6. Close the Printer icon to exit printer configuration. NetBEUI printing 1. To create a printer, double-click the target printer icon to open the Properties dialog box. net use LPT1: \\NetBIOS name of print server\ Device name of print server Note: To change the NetBIOS name and device name, use EpsonNet WinAssist or WebAssist running on Windows. Chapter 5 Installing the Printer Driver 143 Chapter 6 Settings for NetWare Server Introduction to NetWare Settings This chapter explains how to configure the print server for NetWare. First, you need to set up the printer in a NetWare environment, and then configure the print server using EpsonNet WinAssist. Supported systems Server environment NetWare 3. 1/3. 11/3. 12/3. 2 (Bindery) NetWare 4. 1/4. 11/4. 2 (NDS, Bindery emulation) IntranetWare (NDS, Bindery emulation) NetWare 5. 0/5. 1 (NDS, NDPS) NetWare 6. 0 (NDS, NDPS) Client environment The client environment must be supported by NetWare. The clients are able to use the printer driver mounted on the print server. For Windows Me/98/95: Novell Client 3. 3 or higher for Windows 95/98 For Windows XP/2000/NT 4. 0: Novell Client 4. 8 or higher for Windows NT/2000/XP Chapter 6 Settings for NetWare Server 144 About modes You can choose either the Print Server, Remote Printer, or Standby mode. We recommend that you use the Print Server mode unless the number of users exceeds the limit. Print Server mode (NDS/Bindery Print Server): High-speed printing with direct printing Uses the NetWare user account Can connect up to 8 file servers simultaneously Can register up to 32 print queues Remote Printer mode: A NetWare user account is not required. Can attach up to 16 printers for NetWare 3. x, and up to 255 for NetWare 4. x or later. [. . . ] If it does not, you may have incorrectly typed the MAC address or the IP address in the arp -s command. If none of these actions are effective, re-initialize the print server and try again. Print a status sheet to check whether the new IP address has been assigned to the print server. Note: When the IP address is set by the ping command, the subnet mask is automatically changed by the class of the IP address. [. . . ]