User manual EPSON AL-M200

[. . . ] User’s Guide NPD4751-01 EN AL-M200 Series User’s Guide Contents Preface Copyright and Trademarks. 19 Power Off Mode (for users in Euro, the Middle East, Africa, and Russia only). 19 Exiting the Power Off Mode (for users in Euro, the Middle East, Africa, and Russia only). 23 Contents 2 AL-M200 Series User’s Guide Chapter 4 Printer Connection and Software Installation Overview of Network Setup and Configuration. [. . . ] Do not use ink jet paper on your printer. Printing Basics 106 AL-M200 Series User’s Guide ❏ For manually loading print media for duplex (2-sided) printing, see “Manual Duplex Printing (PCL Print Driver Only)” on page 125. ❏ Do not wipe the pink-tinted grease off as doing so may cause paper to misfeed. 1. Hold the tray with both hands, remove it from the printer, and then remove the paper tray cover from the paper tray. Printing Basics 107 AL-M200 Series User’s Guide 2. Hold the paper tray end with one hand, push and hold the paper tray extension lever with the other hand, and then extend the tray to your desired length. Note: The paper tray can accommodate a stack of A5 paper by default, and is designed to extend in two lengths. Slide the paper width guides and the length guide to the maximum positions. Printing Basics 108 AL-M200 Series User’s Guide 4. Before loading the print media, flex the sheets back and forth, and then fan them. Load the print media into the paper tray with the recommended print surface facing up. Note: Do not load paper media above the fill line on the paper width guides of the paper tray as it may cause paper jams. Slide the paper width guides and then the length guide inward until they rest lightly against the edges of the print media stack. Printing Basics 109 AL-M200 Series User’s Guide 7. Hold the paper tray with both hands and push it into the printer until it clicks into place. 9. Open the output tray extension. Printing Basics 110 AL-M200 Series User’s Guide 10. Select the paper type on the print driver if the loaded print media is not standard plain paper. If a user-specified print media is loaded in the paper tray, you must specify the paper size on the print driver. Note: For details on specifying the paper size and type on the print driver, refer to the Help provided for the print driver. Loading Envelopes in the Paper Tray Follow the guidelines below to load envelopes in the paper tray. Note: ❏ When you print on envelopes, be sure to specify the envelope on the print driver. ❏ If you do not load envelopes in the paper tray right after they have been removed from the packaging, they may bulge. To avoid jams, flatten them as shown below before loading them in the paper tray. Printing Basics 111 AL-M200 Series User’s Guide ❏ If envelopes are still not fed correctly, add some bending to the flap of the envelopes as shown in the following illustration. The amount of the bending shall be 5 mm (0. 20 inches) or less. Important: Never use envelopes with a window or coated linings as it causes paper jams that may result in damage to the printer. Loading Com-10, Yougata 4/6, or Younaga 3 Envelopes Load envelopes with the print surface facing up. Ensure that the flapped edge is pointing toward the right of the printer and each flap is folded under the envelope. Printing Basics 112 AL-M200 Series User’s Guide Loading Monarch, DL, or Yougata 2/3 Envelopes You can load Monarch, DL, and Yougata 2/3 Envelopes in either of the following orientations: SEF: Load envelopes with the print surface facing up. Ensure that the flapped edge is pointing toward the right of the printer and each flap is folded under the envelope. LEF: Load envelopes with the print surface facing up. Ensure that the flapped edge is pointing toward the front of the printer and the flaps are left unfolded. Note: ❏ When you load the envelopes in the LEF orientation, be sure to specify the landscape orientation on the print driver. ❏ To confirm the correct orientation of each print media such as envelopes, see the instructions on the Envelope/Paper Setup Navigator dialog box of the print driver. Loading C5, Nagagata 3/4, or Kakugata 3 Envelopes Load envelopes with the print surface facing up. [. . . ] The available numbers that each print driver can print on one sheet of paper are as follows: ❏ ❏ Microsoft Windows Print Driver: 2, 4, 8, or 16 pages Mac OS X Print Driver: 2, 4, 6, 9, or 16 pages Print media Combined with the Duplex (2-sided) print setting, Multiple Up allows you to print up to 32 pages on one sheet of paper. (16 images on the front and 16 on the back) Checking Page Counts You can print the System Settings page to check the total number of printed pages. The total number of printed pages is shown in the Print Volume section, classified by paper sizes. Single side print (including Multiple Up print) is counted as one job, and 2-sided print (including Multiple Up print) is counted as two. [. . . ]