User manual ENVISION H712A

[. . . ] As an ENERGY STAR Partner our company has determined that this product meets the ENERGY STAR guidelines for energy efficiency. 1. WARNING: To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Refer servicing to qualified personnel only. 1 PRECAUTIONS Do not use the monitor near water, e. g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. [. . . ] The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0. 75mm2 or H05VVH2-F2 3G 0. 75mm2) shall be used. Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0. 75mm2) shall be used. 4 CONTROLS AND CONNECTORS VIDEO CABLE Connecting the D-Sub Cable: Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's DSub port. Connecting the Power Cord: Connect the power cord into your LCD monitor's power input socket, and then plug the other end into a 3-pin AC power outlet. The power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor. Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). Connecting the Audio Cable: Plug audio cable between the computer multi-media (or sound) card's audio output and monitor's audio input. Figure 2 1. AC Power Cord D-Sub Cable Audio Cable Connecting Cables 5 ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle from -5 to 20. Figure 3 NOTES Do not touch the LCD screen when you change the angle. Careful attention is required not to catch your fingers or hands when you change the angle. 6 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. The power indicator will light up. Figure 4 External Control Button EXTERNAL CONTROLS 1. MENU/ENTER 7 FRONT PANEL CONTROL Power Button / Power Indicator: Press this button to turn the monitor ON or OFF. Orange -- Off mode. MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Volume Adjust OSD status. Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus. > /Volume: < /Volume: Auto Adjust button / Exit: OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. NOTES Do not install the monitor in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock. [. . . ] For FOCUS and CLOCK adjustment use "dot-pattern" or win 95/98 shutdown mode pattern. 13 ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is properly connected , If the connector is loose, tighten the connector's screws. Check the signal-cable's connection pins for damage. MODE NOT SUPPORTED : Your computer has been set to unsuitable display mode , set the computer to display mode given in the following table (See page 17). 14 APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size Pixel pitch Video Input H-Frequency V-Frequency Display Colors Dot Clock Max. Resolution Plug & Play EPA ENERGY STAR® Input Connector Input Video Signal Maximum Screen Size Power Source Environmental Considerations Dimension Weight (N. [. . . ]