User manual ENVISION EN9250

[. . . ] Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. guidelines for energy efficiency. WARNING: To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Refer servicing to qualified personnel only. 2 EN9250 PRECAUTIONS ! [. . . ] Line up the front of the monitor with the front of the base and press firmly. Remove Pin Remove Base Figure 2 - Installing the Base. Never remove the base while the height adjustment lock pin is installed. Press the four clips inward while pushing the bottom base out. 7 7 EN9250 INSTALLATION INSTRUCTIONS (Cont) POWERCORD Power Source: 1. Make sure that the power cord is the correct type required in your area. This LCD monitor has an internal Universal Power Supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required. ) 3. Connect the AC-power cord into your LCD monitor's AC-power-input. The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 2 2 0. 75mm or H05VVH2-F2 3G 0. 75mm ) shall be used. As an alternate, a flexible cord of synthetic rubber according to IEC 60245 (designation H05RR2 F 3G 0. 75mm ) shall be used. The accessory power cord for the Northern American region is the wall plug with NEMA 5-15 style and is UL listed and CSA labeled. Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of a minimum No. One end terminates with a grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration. The other end terminates with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties. 8 EN9250 INSTALLATION INSTRUCTIONS (Cont) Connecting The Cables Figure 2 1. Audio Cable Turn off your computer before performing the procedure below. Connect the female end of the AC power cord to the AC-in port on the back of the monitor. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. (Optional ­ Requires a video card with DVI port) Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the computer's DVI port. (Optional) - Connect the PC stereo cable between the monitor's audio input and the PC's green audio output port. If not, refer to the FAQ (frequently asked questions) section for troubleshooting. 9 EN9250 INSTALLATION INSTRUCTIONS (cont) How To Install The INF & ICM Files · This is a Plug & Play monitor. Microsoft Windows will automatically install a Plug & Play driver for it when you first install this monitor. [. . . ] Check the signal -cable connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode. Set the computer to a display mode given in the Preset Display Modes table. 20 EN9250 APPENDIX SPECIFICATIONS Driving system Size Pixel pitch Viewable angle Response time Video TFT Color LCD 48cm(19. 0") 0. 294mm( H )x 0. 294mm( V ) LCD Pane Panel Input Display Colors Dot Clock Max. Resolution Plug & Play EPA ENERGY STAR® Input Connector Input Video Signal 140° (H) 140° (V) 16 ms R, G, B Analog Interface Digital interface Separate Sync. H/V TTL H-Frequency 30KHz ­ 83KHz V-Frequency 55-75Hz 16. 7M Colors 135MHz 1280 x 1024 @75Hz VESA DDC 2BTM ON Mode !55W OFF Mode !2W D-Sub 15pin DVI-D 24pin Analog:0. 7Vp-p(standard), 75 OHM, Positive Digital DVI-D Horizontal : 376. 32mm Vertical : 301. 056mm 100~240VAC, 47~63HZ Operating Temp: 0° to 40°C Storage Temp. : -20° to 60°C Operating Humidity: 15% to 90% 422(W)×(444-557)(H)×242(D)mm 7. 8kg Unit (net) Maximum Screen Size Power Source Environmental Considerations Dimensions Weight (N. [. . . ]