User manual ENVISION EN7220

[. . . ] The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. 1. WARNING: To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Refer servicing to qualified personnel only. 2 EN7220 PRECAUTIONS Do not use the monitor near water, e. g. [. . . ] In order for this monitor to operate properly, there must be a video input signal. 5 EN7220 BEFORE YOU OPERATE THE MONITOR FEATURES · · · · · · · 17" (43. 2cm) TFT Color LCD Monitor Crisp & Clear Display for Windows Recommended Resolutions: 1280 X 1024 @ 60Hz ® EPA ENERGY STAR Ergonomic Design with Height, Pivot, Tilt & Swivel Adjustable Stand Height, Pivot, Tilt & Swivel Adjustable Stand Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: Monitor Base Quick Start Guide (QSG) CD (Manual & Drivers) 15-pin D-Sub Cable Power Cord Accessory Cup x 2 Accessory Clip x 2 Warranty Booklet 6 EN7220 INSTALLATION INSTRUCTIONS INSTALLING & REMOVING THE BASE Install Figure 1 - Installing the Base. Line up the front of the monitor with the front of the base and press firmly. Remove Pin Remove Base Figure 2 - Installing the Base. Never remove the base while the height adjustment lock pin is installed. Press the four clips inward while pushing the bottom base out. 7 EN7220 INSTALLATION INSTRUCTIONS (Cont) POWERCORD Power Source: 1. Make sure that the power cord is the correct type required in your area. This LCD monitor has an internal Universal Power Supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required. ) 3. Connect the AC-power cord into your LCD monitor's AC-power-input. The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 2 2 0. 75mm or H05VVH2-F2 3G 0. 75mm ) shall be used. As an alternate, a flexible cord of synthetic rubber according to IEC 60245 (designation H05RR2 F 3G 0. 75mm ) shall be used. The accessory power cord for the Northern American region is the wall plug with NEMA 5-15 style and is UL listed and CSA labeled. Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of a minimum No. One end terminates with a grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration. The other end terminates with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties. 8 EN7220 INSTALLATION INSTRUCTIONS (Cont) Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of a minimum No. One end terminates with a grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration. The other end terminates with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties. Connecting The Cables Figure 2 1. 15-pin D-SUB Cable Turn off your computer before performing the procedure below. Connect the female end of the AC power cord to the AC-in port on the back of the monitor. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. [. . . ] With a wrong phase adjustment the picture has horizontal disturbances in light picture. For FOCUS and CLOCK adjustment use "dot-pattern" or win 95/98 shut-down mode pattern. ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is properly connected , If the connector is loose, tighten the connector's screws. Check the signal -cable connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode. [. . . ]