User manual ENVISION EN7100SSI

[. . . ] The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Warning To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Refer servicing to qualified personnel only. EN-7100s 2 v1_090802 Precautions · Do not use the monitor near water, e. g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. [. . . ] Never use strong solvents such as thinners, benzene, or abrasive cleaners, since these will damage the cabinet. Always unplug the monitor before cleaning it. Using the Right Power Cord The supplied power cord is a NEMA 5-15 style plug. If the monitor will be connected to your computer's power outlet, use a minimum No. 18 AWG, type SJT or SVT three conductors cord with one end terminating with a male grounded plug, rated 10A, 250V, CEE-22. The other end must terminate with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. 4 EN-7100s v1_090802 Before You Operate the Monitor Installing & Removing the Base EN-7100s General Features: · 17" (43. 2cm) TFT Color LCD Monitor · Crisp, Clear Display for Windows · Supports Resolutions up to 1280 X 1024 pixels @75Hz, (1280 x 1024 @ 60Hz Recommended) · EPA ENERGY STAR® · Ergonomic Design · Space Saving, Compact Case Design EN-7100s Package Contents The box that your monitor was shipped in should have included the following items: 1. 5 EN-7100s LCD Monitor Power Adapter Power Cord Windows 95/98/2000/ME/XP INF Driver Disk Quick Start Guide Booklet (Containing Warranty & Safety Information) v1_090802 Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied EN-7100s 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. Connect the power adapter into the DC IN socket on the back of the monitor. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip. Caution: Make sure the power cord is the correct type that is required in your area. This LCD monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required). If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). EN-7100s 6 v1_090802 Before You Operate the Monitor EN-7100s Preparing to Install An Optional Wall Mounting Arm (Not supplied) This monitor can be attached to a wall mounting arm you purchase separately. Remove the base. See next page for further installation instructions. EN-7100s 7 v1_090802 Before You Operate the Monitor Install An Optional Wall Mounting Arm (Not supplied) EN-7100s Follow these steps to finish installing the wall mounting arm: 1. Line up the holes of the arm with the holes in the back of the monitor. Insert the power cable into the slot on the back of the monitor. The Envisionl EN-7100s is compatible with the Ergotron line of mounting and arm solutions. Contact Ergotron at 800-888-8458 or visit their web site at www. ergotron. com for more information on the many ways on which you can mount your Envision LCD monitor. EN-7100s 8 v1_090802 Before You Operate the Monitor Adjusting the Viewing Angle For optimal viewing, adjust the monitor's angle to your own preference. · Hold the stand firmly when you change the monitor's angle. · You can adjust the monitor's angle from -5° to 25°. · Be careful to avoid pinching your hand in the swivel base. EN-7100s How to Install INF & ICM File 1. Insert the Windows 95/98/2000/ME/XP INF Driver Disk into your floppy drive. If the wizard asks for the location of the driver file, select drive A and press Next. EN-7100s 9 v1_090802 Operating Instructions Front Panel Buttons EN-7100s Auto: Press this button to automatically set the H-Position, V-Position, Clock and Focus settings. Brightness: Press this button to adjust the picture's brightness. [. . . ] With a wrong phase adjustment the picture has horizontal disturbances with very light screen images. Note: For FOCUS and CLOCK adjustment use "dot-pattern" or Win 95/98 shut-down mode pattern. Error Message Cable not connected Possible Solution · Make sure the video cable is properly connected to the computer. · Inspect the video cable and make sure that none of the pins are bent. 14 v1_090802 EN-7100s Technical Support (FAQ) Error Message Input not supported EN-7100s Possible Solution · Your computer has been set to an incompatible display mode. Click the Settings tab then set your computer's display mode to one of the settings listed in the resolution chart below. [. . . ]