User manual ENVISION EN5400

[. . . ] that this 3 PRECAUTIONS: · Do not use the monitor near water, e. g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. · Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. [. . . ] Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. The LCD panel used in this monitor is a very high technology product with 2, 359, 296 thin film transistors giving you fine picture details. Occasionally, a few non-active pixels may appear on the screen as a fixed point of red, green, blue, white or black. Due to the nature of the LCD screen, an after-image of the previous screen may remain after switching the image when the same image has been displayed for a long time. Due to this, an interpolation is necessary to operate the monitor in a resolution below its native resolution which may slightly de-grade the display quality. Therefore, it is highly recommended to operate this monitor at its native resolution of 1024x768 @ 60Hz. · · · · OTHER NOTES · The screen surface is very soft. Do not rub, touch or tap the screen surface with sharp object such as pen or pencil. Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor. For maximum protection, repackage your monitor as it was originally packed at the factory. To keep the monitor looking new, periodically clean the case & surface of the TFT-LCD panel with a soft non-fibrous cloth lightly dampened with a glass cleaner. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the case & panel. As a safety precaution, always unplug the monitor before cleaning it. · · · · 5 GETTING STARTED WARNING: Do not operate the LCD monitor with unspecified power supply. Usage of incorrect voltage will cause malfunction and may cause fire or electric shock. Introduction Bright and sharp images of text and graphics are what you will find with your LCD color monitor. The LCD monitor provides a maximum resolution of 1024 x 768 pixels with a flicker-free display at up to 75Hz refresh rates that offers bright, sharp and vibrant color display without the radiation emission and hazards of CRT monitors. Features 15" (38. 1cm) TFT Color LCD Monitor Supports XGA resolution of 1024 x 768 pixels ® EPA ENERGY STAR Digital Character Smoothing Automatic Set-Up Windows 95/98/2000/XP Plug & Play Compliant Versatile, functional & User friendly OSD Plug & Play: Conform to the VESA standards and support DDC1/2B spec. Unpacking and Checking the Package Contents Before unpacking your LCD Monitor, prepare a suitable workspace for your LCD Monitor and computer. Set the LCD Monitor box in an upright position and open from the top of the box before removing the right/left cushions. 2. Remove the back cover from your monitor (pull from the bottom of cover to open) to install your PC system. Accessories 1 pc Signal Cable (Already Built-in) 1 pc AC/DC Adaptor 1 pc Power Cord 1 pc 1 pc QSG CD User's Manual (Quick Start Guide) Installing the Monitor DO NOT install the monitor where sudden temperature changes may occur, or in humid, dusty, or smoky areas as it may cause fire, electric shock or damage. DO NOT place your LCD Monitor near a window as it may be severely damaged if exposed to rain, water, moisture, or sunlight. MAINTAIN good ventilation; covering of ventilation slots or holes may cause fire. SAFE storage temperature of the LCD Monitor is in a range of -20 to +65. 6 Installing the Base and Connecting the Cables 1. Take the monitor out from the box and place it on the table, with the front side facing down. Note: Make sure the surface of the table is clean and covered with a soft cloth to prevent damaging or scratching the panel when assembling the LCD monitor. 3. Take off the plastic cover at the top of the stand of the LCD monitor. 4. Pull up the stand of the LCD Monitor (max. 25°) to connect the cables. 5. Put the power cord and signal cable through the hole on the stand. 6. Connect signal cable and DC adapter connector to your Monitor. [. . . ] (3) Check the "POWER MANAGEMENT" function is operated correctly. 12 CONFORMITY AND COMPLIANCE FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ]