User manual ENVISION EN5100E

[. . . ] The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Warning To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Refer servicing to qualified personnel only. EN-5100e 2 31MY02 For Your Safety Precautions · Do not use the monitor near water, e. g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. [. . . ] Be sure to repackage your monitor as it was originally packed at the factory. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinners, benzene, or abrasive cleaners, since these will damage the cabinet. Always unplug the monitor before cleaning it. Using the Right Power Cord The supplied power cord is a NEMA 5-15 style plug. If the monitor will be connected to your computer's power outlet, use a minimum No. 18 AWG, type SJT or SVT three conductors cord with one end terminating with a male grounded plug, rated 10A, 250V, CEE-22. The other end must terminate with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. 4 31MY02 EN-5100e Before You Operate the Monitor Installing & Removing the Base EN-5100e General Features: · 38. 1cm(15") TFT Color LCD Monitor · Crisp, Clear Display for Windows · 1024 X 768 @ 75Hz (Maximum & Recommended Resolution) · EPA ENERGY STAR ® · Ergonomic Design · Space Saving, Compact Case Design EN-5100e Package Contents The box that your monitor was shipped in should have included the following items: 1. Windows 95/98/2000/ME INF Driver Disk 5 31MY02 Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied EN-5100e 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. Connect the power cord into your LCD monitor's power input socket. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip. Caution: Make sure the power cord is the correct type that is required in your area. This LCD monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required). If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). EN-5100e 6 31MY02 Before You Operate the Monitor EN-5100e Connecting the Wires Using An Optional Power Cord (Not Supplied) The power cord supplied with your monitor can only be connected to a grounded electrical wall socket or power strip. If you wish to connect your monitor to a power supply using the power input socket on the back of your computer, you must purchase a power cord with CEE-22 terminated connectors (see illustration above). Follow these steps: 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. Connect the power cord into your LCD monitor's power input socket. Plug the other end of the power cord into the power output socket on your PC. EN-5100e 7 31MY02 Before You Operate the Monitor Adjusting the Viewing Angle EN-5100e For optimal viewing, adjust the monitor's angle to your own preference. · Hold the stand firmly when you change the monitor's angle. · You can adjust the monitor's angle from -5° to 45°. · Do not touch the LCD screen when you change the angle. · Be careful to avoid pinching your hand in the swivel base. EN-5100e 8 31MY02 Operating Instructions Front Panel Buttons EN-5100e Auto: Press this button to automatically set the H-Position, V-Position, Clock and Focus settings. Brightness: Press this button to adjust the picture's brightness. [. . . ] · Inspect the video cable and make sure none of the pins are bent. · Make sure your computer is operating correctly by pressing the CAPS LOCK key and observing whether the CAPS LOCK light turns ON or OFF. · Inspect the video cable and make sure that none of the pins are bent. EN-5100e 13 31MY02 Technical Support (FAQ) Error Message Input not supported EN-5100e Possible Solution · Your computer has been set to an incompatible display mode. Click the Settings tab then set your computer's display mode to one of the settings listed in the resolution chart below. [. . . ]