User manual ENVISION EFT920

[. . . ] The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Warning To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Refer servicing to qualified personnel only. EFT920 2 v1_031004 For Your Safety Precautions · Do not use the monitor near water, e. g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. [. . . ] · The wall socket should be installed near the equipment and should be easily accessible. EFT920 3 v1_031004 For Your Safety General Notes · Do not install the monitor near heat sources such as radiators or air ducts. · Do not place monitor in direct sunlight or in areas with excessive dust, mechanical vibration or shock. · Save the original shipping carton and packing materials in case you need to ship your monitor. Be sure to repackage your monitor as it was originally packed at the factory. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinners, benzene, or abrasive cleaners, since these will damage the cabinet. Always unplug the monitor before cleaning it. EFT920 General Features: · 19" (48. 3 cm) Color Monitor · Crisp, Clear Display for Windows · Supports Resolutions up to 1600 X 1200 pixels @75Hz · EPA ENERGY STAR® Package Contents The box that your monitor was shipped in should have included the following items: 1. Booklet (containing Warranty and Safety information) Using the Right Power Cord The supplied power cord is a NEMA 5-15 style plug. If the monitor will be connected to your computer's power outlet, use a minimum No. 18 AWG, type SJT or SVT three conductors cord with one end terminating with a male grounded plug, rated 10A, 250V, CEE-22. The other end must terminate with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. EFT920 4 v1_031004 Before You Operate the Monitor Installing & Removing the Base EFT920 EFT920 5 v1_031004 Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied EFT920 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip. Caution: Make sure the power cord is the correct type that is required in your area. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required). If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). EFT920 6 v1_031004 Operating Instructions Front Panel Buttons EFT920 Exit: Press this button to save changes and close the OSD window. Brightness: Press this button to adjust the picture's brightness. If the OSD window is open, this button allows you to move within the window and select desired functions. If the OSD window is open, this button allows you to move within the window and select desired functions. MENU: Press this button to open the OSD window or select a highlighted function. On-screen Display (OSD): Press the MENU button to open the OSD window and adjust settings on your monitor. (See next page. ) EFT920 7 v1_031004 Operating Instructions Adjusting the OSD Settings EFT920 1. Press the < or > buttons until the desired function is highlighted. Press the < or > buttons to change the settings of the function. EFT920 5. [. . . ] · Make sure the Envision monitor drivers are installed (ENVISION monitor drivers are available at: www. ENVISIONmonitor. com) · Adjust the Contrast and Brightness settings. · Press a key on the keyboard or wiggle the mouse to re-activate the monitor. · Make sure the video cable is properly connected to the computer. · Inspect the video cable and make sure none of the pins are bent. [. . . ]