User manual ENVISION A42HD84

[. . . ] Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. [. . . ] Use Auto channel search in "Setup Menu" to search all channels in your location. After Auto channel search is completed, press "CHup" or "CHdown" key on remote control to select the next lower or higher channel. Refer to the following pages for operating procedures: Remote Control ­ page 9. TV Channel Arrangement ­ page 14. POWER KEY Ch14. 0 12:00AM TV channel information 6 Connection to other equipment Please connect this TV Set to other equipment as picture below. You may have many types of equipment as: DVD, VCD, VCR, Set Top Box, X-Box and so on. (View from back of the TV set, left to right) INPUT CONNECTION OF VIDEO SIGNAL(DVD/VCD/VCR) AV1-INPUT s-video Y W R B s-video Y R W Connection to other equipment 7 Connection to other equipment We have 2 component signal input jacks: Y Cb Cr and Y Pb Pr. If your DVD or Set Top Box have Y Cb Cr or Y Pb Pr output, you can connect it to Y Cb Cr or Y Pb Pr input jack. Some DVD or Set Top Box need to set to Y Cb Cr or Y Pb Pr output Notice: If you see that display abnormality in screen, you need to check the cable connection and DVD setup. G B R R W INPUT CONNECTION OF PC SIGNAL(PC/DVD) Notice: If you see that display abnormality in screen, you need to check the cable connection and DVD setup. Notice: The PC output can not set out of range. The highest resolution input is 1280 X 1024 / 60Hz. Some PC models cannot be connected to the set. 24PIN DVI R/L INPUT 15PIN VGA R/L INPUT Notice:If your DVD doesn't have 3. 5 earphone output jack, Please use cable from RCA to3. 5 earphone jack to connect. D-SUB 15 Pin: Connect D-SUB signal cable VGA cable from PC to D-SUB jack at the back of this display. And connect the earphone cable from PC earphone output jack to AUDIO input jack near to the D-SUB jack. Setup: Use the key "Digital" Remote Control Transmitter or "MODE" on Front panel controls in key to select source to "VGA"state. DVI-D: Connect DVI-D 24 Pin signal cableTMDS cablefrom equipment with DVI-D jack to the back of this display. And connect earphone cable from equipment with earphone output jack to AUDIO input jack near the DVI-D jack. Setup: Use the key "Digital" Remote Control Transmitter or "MODE" on Front panel controls in key to select source to "DVI"state. Auto channel scan menu displays channel number being scanned. Manual Channel Set Menu Displays all the channel numbers that are found. Add or delete Channel number. Channel Labels Menu allows user labeling. 10 OSD Menu Descriptions Video Menu . Press " " or " " to move the cursor up or down the sub-item list. Press " " or " " to adjust the value of the sub-item. Press "Enter" again to exit the sub-item. Contrast: Contrast adjustment, 0 ~ 100. Press " " or " " to move the cursor up or down the sub-item list. Press " " or " " to adjust the value of the sub-item. [. . . ] Check the DTV signal via Menu --> Setup --> DTV Signal Adjust the direction of your antenna to improve the signal Re-install the channels if needed. ·Check cars/motorcycles. No Picture, No Sound Interference, Noisy ·Check antenna connection, aerial location, and direction Re-scan Channels. Distorted picture, Noisy ·Check whether colour setting is at minimum. Normal Colour, No Sound 16 Troubleshooting The plasma TV panel is manufactured using an extremely high level of precision technology, however, sometimes some parts of the screen may be missing picture elements or have luminous spots. [. . . ]