User manual ENGENIUS SN-900 INSTALL GUIDE

[. . . ] If you have any reason to suspect that interference is taking place, turn off your handset immediately. For hands-free operation of the handset, the device has been tested for RF exposure compliance with the EnGenius brand belt-clip and leather pouch. Other belt-clips, holsters or similar accessories that have not been tested may not comply with RF exposure requirements and should not be used. Congratulations! You have purchased an exceptional business communications tool from the leading Industrial Cordless TM Phone System manufacturer. The EnGenius SN-900 ULTRA Industrial Cordless Phone System is the second generation of the Longest Range Cordless Phone and 2-Way Radio system. [. . . ] Verify base unit's power light is on and turn on the handset power by pressing and holding the END key for 2 seconds. Each base can have 9 handsets primarily registered to it, and each handset can be registered to 4 base units. Valid handset ID numbers will be 11-19, 21-29, 31-39 and 41-49, with the first digit indicating the base ID number and the second digit indicating the handset number. The handset ID number does not change after primary registration for handsets that are registered to a secondary base unit. * Base has already registered maximum number of handsets (9) it can support. A handset must be deregistered before a new one can be added to the system. No connection Table full ~ 38~ * Handset registered to a base with same ID. ID Conflict Base X 4. Deregistration is successful. Dereg from all bases NOTE 1: Upon successful registration, your handset will display "Reg OK New ID = " NOTE 2: Your handset will automatically exit the REGISTRATION mode after 30 seconds. The handset ID number in the middle of the top line of the handset display will not change after registering the first base unit (known as the primary base unit). The handset has now been de-registered from all base units. The handset ID number will be reset to "00" as seen in the middle of the top LCD line. De-Registering a Handset from a Single Base Unit 1. Press and hold the VOLUME and PAGE buttons on the base the handset is to be de-registered from until there is a beep. The LCD will read: " Dereg from base X " when de-registration is complete. SECURITY FUNCTION: A third option is available for deregistering all the handsets at once and generating a new base ID code (system registration reset). While in the Main Menu, press the "2" key to select DIRECTORY: 3. Information in the Phone Directory is stored vertically, as shown in Table 1 below. The up and down arrow keys are used to move through the directory records. ADD Main Menu: ¡ ¡ õô 1:KEY GUARD 2:DIRECTORY 3:CALLER ID 4:SOUNDS 5:SETTINGS 6:REGISTER * Press the LEFT SOFT FUNCTION key to select ADD. * If the directory is full, the following will be displayed on the LCD: Memory full Table 1 Index Code 01 Information Name # 1 Telephone # 1 02 Name # 2 Telephone # 2 * If there are available spaces, the first 30 Name # 30 Telephone # 30 empty space will be accessed automatically and the following screen will appear: * To return to the DIRECTORY VIEW mode, press the LEFT SOFT FUNCTION key. OK Number?SAVE DELETE Note: Press the RIGHT SOFT BUTTON and enter the Index Code to dial the phone directory number. * If information is to be stored in a specific location, use the scrolling keys to find the correct location for the new information. The location number will appear as a 2 digit number to the left of the battery icon. ~ 43~ ~ 44~ * Select ADD again using the LEFT SOFT FUNCTION key. The following screen will then appear: 1. Enter a new phone number by pressing the corresponding keypad number key once. Note: The following characters require a special key combination: Space: press the # key two times (# # ). T enter the letters of a name, press o the corresponding keypad number one or more times depending on the order to the characters on the key. See T able 2 for a listing of available characters that can be used in the name field. For example: press "2" once for the letter "A, " twice for the letter "B, " etc. NOTE: In the name editing mode, as indicated on the LCD prompt, all letters will automatically be entered in the upper case. [. . . ] Periodically clean the charge contacts on both the charger and handset. Position positive (+ ) battery contact to match diagram in cordless handset. Charge the batteries provided with, or identified for use with, this product only in accordance with the instructions and limitations specified in the instruction manual. Exercise care in handling batteries in order not to short the batteries with conducting materials such as rings, bracelets, and keys. [. . . ]