User manual ENGENIUS EL-2611CB5-

[. . . ] IEEE 802. 11b Outdoor Wireless Client Bridge User Manual November 03, 2004 Version 1. 00 Contents CHAPTER 1. 1. 1 1. 2 1. 3 1. 4 1. 5 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 INTRODUCING THE WIRELESS CLIENT BRIDGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 PRODUCT FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Apply the New Settings Step 1 Enter the Utility > Administration page, select the Save then Restart to apply the new configuration settings. Step 2 Click FINISH to take effect on the previous configuration changes. Hint: It takes about 10 seconds, to complete the restart process. Version 1. 02 14 Version 1. 02 15 2. 4. 7 Upgrade the Firmware Setup your TFTP Server The Trivial File Transfer Protocol (TFTP) Server allows you to transfer files across a network. You can download the firmware files for Wireless client bridge upgrades. After the TFTP Server is installed, make sure you have the proper TFTP Server IP address, the proper Wireless client bridge firmware files, and the TFTP Server is operational. Update the Firmware using the TFTP method Step 1 Enter the Utility > Software Upgrade page as shown in the figure below, and can use TFTP to upgrade Wireless client bridge. Here, user must specify the TFTP server IP and select which file you want to upgrade it (Program image, Web image), then click OK button to start the TFTP upgrade process. Step 2 If the upgrade process is success, the Wireless client bridge will apply the new settings and start rebooting right away. Hint: You must set up a TFTP Server and this server must contain the latest new image files. Upgrade the Firmware using RS-232 console Please refer to Provision 2. 4. 3 that introduces how to use RS-232 console port. Step 1 If the connection is normal, when the Wireless client bridge is powered up, the "Current Network Status" will be displayed as Version 1. 02 16 Version 1. 02 17 shown below. Step 2 Press <Esc> keystroke to reboot the Wireless client bridge. Press <x> key during the boot process, and it will display prompt character NetARM> as the figure shown in the next page. Step 4 Select "F -- upgrade Flash memory" and it will display upgrade items for selection as the figure shown below. Step 3 Press "h" keystroke, it will display related commands as the figure shown below. Step 5 Select "3: SOHO" and select "4: WEBIMG" to update the firmware files one by one. Step 6 While the window starts to display "C" character continuously, click Transfer and select the new firmware files <soho. bin> file, press "OK" to start to transfer file to Wireless client bridge. The procedures are the same with upgrading SOHO file (go back to step 5), but should select <pfs. img> file correctly for WEBIMG file upgrade. Step 8 After the upgrade completes, remember to press "R" keystroke to reboot the system. Note: The default transfer protocol is using "Xmodem", so please make sure you select correct protocol to download/upload files when you try to upgrade the Wireless client bridge's firmware files. Version 1. 02 18 Version 1. 02 19 2. 4. 8 Back-up the Wireless client bridge's Configuration Files After configuring Wireless client bridge, user can back-up the configuration files. User can upload the latest back-up files and recover the Wireless client bridge configuration to the settings specified in the back-up files. Downloading Configuration Files Just being the same with firmware upgrade procedures. After the prompt character NetARM> is displayed, select "S ­ Save image to file", and then select "6: CONFIG" to back-up the Wireless client bridge configuration as the figure shown below. Note: Remember to press "R" to reboot the system after you upload the configuration file to the Wireless client bridge Uploading Configuration Files To upload an configuration file to Wireless client bridge, user should select "F -- upgrade Flash memory" and then select "6: CONFIG". While the window starts to display "C" character continuously, click Transfer and select the preferred <CONFIG. IMG>, then press OK to start transferring file to Wireless client bridge. Version 1. 02 20 Version 1. 02 21 Chapter 3. [. . . ] SSID BSSID Channel Type Encrypt Signal Link Status Current SSID SNR( C / I ) RSL Noise Level Current Channel Current Tx Rate Version 1. 02 40 Version 1. 02 41 Chapter 6. Specifications 6. 1 Hardware Specifications General Radio Data Rate Client Interface Range (Open environment) 11, 5. 5, 2 and 1 Mbps, Auto Fall-Back 10/100Base-T Ethernet 300m @ 11. 0Mbps 400m @ 05. 5Mbps 500m @ 02. 0Mbps 800m @ 01. 0Mbps FCC Part 15 EN 300 328-1 EN 300 328-2 EN 301 489-1 EN 301 489-17 EN 60950 IP67 DGT Fully interoperable with IEEE802. 11b compliant products Input: 100~240V, 50~60Hz Output: 24V, 830mA Operation Channels Transmit Power Antenna Sensitivity @ FER=0. 08 DBPSK (1Mbps) North America11 Japan14 Europe13 Spain2 France4 10dBm (ETSI) 19dBm (FCC) External 5dBi dipole antenna, or Embedded 9dBi patch antenna 11. 0 Mbps < -85dBm 05. 5 Mbps < -88dBm 02. 0 Mbps < -91dBm 01. 0 Mbps < -93dBm Regulatory & Safety Certifications Environmental Temperature Range Humidity (non-condensing) Physical Specifications Dimensions Weight 138. 7mm x 104. 0mm x 38. 0mm 500g Operating: 0 to 55 Storage: -20 to 75 5% to 95% typical Compatibility Power Supply (AC/DC Power Adaptor) Network Information Network Architecture Access Protocol Roaming Security Radio Specifications Frequency Band Radio Type Modulation Version 1. 02 Infrastructure (with Wireless client bridge) CSMA/CA IEEE802. 11b compliant 64-/128-bit data encryption 2. 4 ­ 2. 484 GHz Direct Sequence Spread Spectrum (DSSS) CCK (11, 5. 5Mbps) DQPSK (2Mbps) 42 Version 1. 02 43 6. 2 Software Specifications Protocol TCP/IP DHCP Client 802. 1d Transparent Bridging 64-/128-bit WEP encryption MAC address based access control Web-based Manager Console (RS-232) configuration SNMP v1 SNMP MIB-II Private MIB TFTP (Trivial FTP) Xmodem, 1K Xmodem Zmodem Chapter 7. Default Settings 7. 1 General Configuration Security Management 7. 1. 1 System Parameter Host Name Description Host name for the RB Default Value ISP Disable 192. 168. 2. 1 255. 255. 255. 0 192. 168. 2. 254 IP Use MAC Addr. Bridge IP Address Bridge Subnet Mask Default Address Gateway IP You can choice IP produced method . For Wireless Client Bridge with Operation Mode IP address of the gateway for default route when TCP/IP filtering Firmware upgrade 7. 1. 2 SNMP 7. 1. 2. 1 Index 1 Index 2 Index 3 Index 4 Index 5 Index 1 Index 2 Index 3 Index 4 Index 5 Index 1 Index 2 Index 3 Index 4 Index 5 Table of SNMP Community Pool Description Enable or disable the function of the corresponding community index Default Value Enable Enable Disable Disable Disable Read Write ------public private ------- Parameter Validity Access Right Select the access right (Deny/Read/Write/Create) for SNMP Manager Specify the type of community (public or private) for SNMP Community Manager Version 1. 02 44 Version 1. 02 45 7. 1. 2. 2 Table of SNMP Trap Community Host Pool Description Select or disable the SNMP Version Version 1: MIB1 Version 2: MIB2 Default Value Version1 Version2 ------192. 168. 2. 100 192. 168. 2. 100 ------public public ------- Parameter Index 1 Index 2 Index 3 Version Index 4 Index 5 Index 1 Index 2 Index 3 Index 4 Index 5 Index 1 Index 2 Index 3 Index 4 Index 5 Key Panel Specify the IP address of the SNMP Manager for SNMP Trap IP Address Report When you use WEP to communicate with the other wireless clients, all the wireless devices in this network must have the same encryption key or pass phrase. [. . . ]