User manual ENFACE ENVISION 220

[. . . ] Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes. [. . . ] Press Enter and select (if applicable) the Strip Size (best set to default). Press Enter to Create Volume. 7 - 4 Setting Up SATA RAID or AHCI Modes Modules 9. This will now return to the main menu. Intel(R) Matrix Storage Manager option ROM v6. 0. 0. 1022 ICH8R wRAID5 Copyright (C) 2003-06 Intel Corporation. 4. ] Create RAID Volume Delete RAID Volume Reset Disks to Non-RAID Exit [ DISK/VOLUME INFORMATION ] RAID Volumes: ID Name 1 My RAID Physical Disks: Port Drive Model 1 HDT722516DLA380 4 ST380811AS Level RAID0(Stripe) Strip 128KB Size 149. 1GB Status Normal Bootable Yes Serial # VDK71GTE17AH6K 5PS196TS Size 153. 4GB 74. 5GB Type/Status(Vol ID) Member Disk(0) Member Disk(0) 7 [ ]-Select [ESC]-Exit [ENTER]-Select Menu 11. Select 4. Exit and press Enter, then press Y to exit the RAID configuration menu. As the computer starts up, press a key when you see the message "Press any key to boot from CD". Press Enter to continue installing the operating system as normal (see your Windows documentation if you need help on installing the Windows OS). Install the Windows drivers as per Table 4 - 1, on page 4 - 3, including the Intel Matrix Driver (see overleaf) Setting Up SATA RAID or AHCI Modes 7 - 5 Modules 7 Figure 7 - 3 Intel(R) Matrix Storage Console Intel Matrix 1. Insert the Device Drivers & Utilities + User's Manual CD-ROM (Win Vista) into the CD/DVD drive. The Intel Matrix Storage Console displays status information on your RAID configuration. The Intel(R) Matrix Storage Manager provides information on the RAID status. 7 - 6 Setting Up SATA RAID or AHCI Modes Modules Wireless LAN Module If you have included either an Intel PRO/Wireless 3945ABG (802. 11a/b/g) PCIe WLAN module, or 802. 11b/g USB WLAN module, in your purchase option the LED will be green. Insert the Device Drivers & Utilities + User's Manual CD-ROM (Win Vista) into the CD/DVD drive. The operating system is the default setting for Wireless LAN control in Windows Vista (see overleaf). 7 Wireless LAN Module 7 - 7 Modules Connecting to a Wireless Network 1. Click the taskbar wireless icon , and then click Connect to a network (or rightclick the icon , and then click Connect to a network). Figure 7 - 4 Taskbar Menus Click icon Right-click icon 7 Network and Sharing Center You can also use the Network and Sharing Center control panel in Windows (Network and Internet) to connect to any available wireless networks. 2. 3. In the Show list, click to choose Wireless from the drop-down menu. A list of currently available networks will appear. Figure 7 - 5 Connect to a Network 7 - 8 Wireless LAN Module Modules 4. If you do not see a network you want to connect to, click Set up a connection or network (a list of options will appear allowing manual searching, and creating a new network). Figure 7 - 6 Connecting 7 6. Move the cursor over the taskbar icon to see the connection status (see below). Figure 7 - 7 Connection Status Wireless LAN Module 7 - 9 Modules 7. Security Enabled Networks You should try to make sure that any network you are connecting to is a secure network. Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc. To disconnect from the wireless network you can click the taskbar wireless icon , and then select Connect or disconnect to access the network menu, and click Disconnect (or right-click the icon , and then click Disconnect from). Click icon 7 Figure 7 - 8 Disconnecting Right-click icon 7 - 10 Wireless LAN Module Modules Bluetooth Module If you have included a Bluetooth module in your purchase option the be orange. Insert the Device Drivers & Utilities + User's Manual CD-ROM (Win Vista) into the CD/DVD drive. Click the button to accept the license agreement, and then click Next. You can configure the settings at any time by going to the IVT Corporation BlueSoleil - Main Window (Start > Programs/All Programs > IVT BlueSoleil > BlueSoleil), or by clicking the desktop icon . 7 Bluetooth Module 7 - 11 Modules User Guides & Help View the BlueSoleil User Guides from the Help Menu (or press the F1 key) in the IVT Corporation BlueSoleil Main Window control panel. 7 Click the Help menu and select Contents and Index. [. . . ] Go to the Advanced menu. · For RAID Mode: - Set "SATA RAID Enable" ("SATA RAID Enable: (Advanced Menu)" on page 5 - 9) to "Enabled". OR · For AHCI Mode: - Set "SATA AHCI Enable" ("SATA AHCI Enable: (Advanced Menu)" on page 5 - 9) to "Enabled". 9. Set the external CD/DVD-ROM Drive (make sure the Microsoft Windows OS CD is inserted) as the first device in the boot order from the Boot menu. Attach the external USB floppy disk drive to one of the computer's USB ports. [. . . ]