User manual ENCORE ENUWI-N

[. . . ] Encore 802. 11n Wireless USB Adapter User's Guide FCC Certifications Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that If this equipment does cause interference will not occur in a particular installation. harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -Reorient or relocate the receiving antenna. [. . . ] Please refer to the following chart for definitions of each item. Wireless mode Enable TX Burst Click the drop list to select a wireless mode. Select to enable connecting to a TX Burst supported device. Enable TCP Window Mark the checkbox to enable TCP window size, which help enhance throughput. Show Authentication Status Dialog Enable CCX (Cisco Compatible extensions) Mark the checkbox to show "Authentication Status Dialog" while connecting to an AP with authentication. Authentication Status Dialog displays the process about 802. 1x authentication Select to enable CCX. This function can only be applied when connecting to a Cisco compatible device. 20 Statistics Statistics page displays the detail counter information based on 802. 11 MIB counters. This page translates the MIB counters into a format easier for user to understand. Frames Transmitted Successfully Frames successfully sent. Frames Fail To Receive Frames failed transmit after hitting retry limit ACK After All Retries RTS Frames Successfully Receive CTS RTS Frames Fail To Receive CTS Frames Retransmitted Successfully Restart Counter Successfully receive CTS after sending RTS frame Failed to receive CTS after sending RTS Successfully retransmitted frames numbers Reset counters to zero 21 Frames Received Successfully Frames Received With CRC Error Frames received successfully Frames received with CRC error Frames Dropped Due To Frames dropped due to resource issue Out-of-Resource Duplicate Frames Received Duplicate received frames. 22 WMM This page allows users to activate the WMM function for this device. Please note that this function only works while connecting to a WMM compatible device. WMM Enable WMM - Power Save Enable Direct Link Setup Enable Enable Wi-Fi Multi-Media. Please enable WMM before configuring this function. 23 WPS WPS Configuration: The primary goal of Wi-Fi Protected Setup (Wi-Fi Simple Configuration) is to simplify the security setup and management of Wi-Fi networks. This adapter supports the configuration setup using PIN configuration method or PBC configuration method through an internal or external Registrar. WPS AP List Display the information of surrounding APs with WPS IE from last scan result. List information include SSID, BSSID, Channel, ID (Device Password ID), Security-Enabled. List information include Authentication Type, Encryption Type, Config Methods, Device Password ID, Selected Registrar, State, Version, AP Setup Locked, UUID-E and RF Bands. List information include SSID, MAC Address, Authentication and Encryption Type. If STA Registrar, RaUI creates a new credential with WPA2-PSK/AES/64Hex-Key and doesn't change until next switching to STA Registrar. Command connect credentials to the next network inside Rescan Information PIN Code Config Mode Table of Credentials Detail Connect Rotate 24 Disconnect Stop WPS action and disconnect this active link. And then select the last profile at the Profile Page of RaUI if exist. If there is an empty profile page, the driver will select any non-secure AP Delete an existing credential. If there is an empty credential, the driver will select any non-security AP. Start to add to Registrar using PIN configuration method Start to add to AP using PBC configuration method. Display rate of progress from Start to Connected status Display currently WPS Status Delete PIN PBC WPS associate IE WPS probe IE Progress Bar Status Bar Note: When you click PIN or PBC, please don't do any rescan within two-minute connection. If you want to abort this setup within the interval, restart PIN/PBC or press Disconnect to stop WPS action. 25 Appendix Introduction to the configuration utility for Vista Users This utility helps Vista users to configure the wireless network. Please refer to the following sections for introduction. Profile This profile page allows users to save different wireless settings, which helps users to get access to wireless networks at home, office or other wireless network environment quickly. 26 To add a new profile: 1. Note: you could also add a new profile quickly by selecting an available network in the "Site Survey" function then press the "Add to Profile" button. [. . . ] If the connection can't be established successfully, station will perform the WPS profile rotation repeatedly. Disconnect from WPS AP: Click the "Disconnect" button to stop the WPS connection. Delete WPS profile: Click the "Delete" button to delete the selected WPS profile. 33 AP mode management guide This adapter can be configured as AP mode. To function this adapter as an AP, please right click the icon on system tray and select "Switch to AP mode". [. . . ]