User manual ENCORE ENUWI-G

[. . . ] When nearby persons has to be kept to ensure RF exposure compliance, in order to comply with RF exposure limits established in the ANSI C95. 1 standards, the distance between the antennas and the user should not be less than 20 cm. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. [. . . ] 16 iv INTRODUCTION Congratulations on your purchase of this IEEE 802. 11g Pen Size Wireless USB 2. 0 Adapter. This manual helps to get familiar with the Pen Size Wireless USB 2. 0 Adapter. This manual contains detailed instructions in operation of this product. With a Wireless LAN (IEEE 802. 11g) USB 2. 0 Adapter, a desktop or laptop computer can communicate with another computer in a wireless way. Easy-to-use utilities are bundled with Wireless USB Adapter for configuration, monitoring, and diagnosis purposes. Pen Size Wireless USB 2. 0 Adapter can wirelessly transmit and receive data, minimizing the need for wired connections, at a speed of up to fifty-four megabit per second. Wireless USB 2. 0 Adapter provides users with an access to real-time information anywhere in their organization. The mobility provides productivity and service, which are not available under wired networks. The Wireless USB 2. 0 Adapter configuration is easy to change from peer-to-peer networks, suitable for a small number of users, to full infrastructure networks of thousands of users that allow roaming around a broad area. Overview of this User's Guide Introduction. Helps you get started with the basic installation of the Wireless USB 2. 0 Adapter. Lists the technical (general, physical and environmental) specifications of the Wireless USB 2. 0 Adapter. 1 UNPACKING AND SETUP This chapter provides unpacking and setup information for the Wireless USB 2. 0 Adapter. Unpacking Open the box of the Pen Size Wireless USB 2. 0 Adapter and carefully unpack it. The box should contain the following items: One 802. 11g Pen Size Wireless LAN USB 2. 0 Adapter One Driver & Utility CD-ROM One A-type USB male to female extension cable If any item is found missing or damaged, please contact your local reseller for replacement. Setup The setup of the Wireless USB 2. 0 Adapter can be performed using the following steps: Visually inspect the USB connector and make sure that it is fully plugged in to the system's USB port. Make sure that there is a well environment that there is no much intrusion to have a better connection. Connecting the USB Extension Cable The USB extension cable that comes with the Adapter has Type A connectors on both ends. One is a male Type A connector that plugs into the PC's USB port, and the other is a female Type A connector that plugs into the Adapter. This USB extension cable have a special function, it can be twist to any direction to have the best connection in the air. It is recommended that the Pen Size Wireless USB Adapter was vertically plane with the ground. 2 HARDWARE INSTALLATION LED Indicator LNK (LINK) The LNK indicator lights green when the Wireless LAN is connected to a network successfully. Otherwise the LNK indicator blinks green while the Wireless USB Adapter is scanning the wireless device. Check the installation The LEDs of the Wireless USB 2. 0 Adapter are clearly visible and the status of the network link can be seen instantly: 1. When connected to the USB port and the driver was installed, the LNK LED will start blinking, it means that the device is starting to scanning a 802. 11g wireless device near the Wireless USB 2. 0 Adapter. While the Wireless USB 2. 0 Adapter linked up to the Access Point or to other Wireless LAN station, the LNK LED will always light up. 3 SOFTWARE INSTALLATION This section will lead you to install the driver and utility of the Wireless USB 2. 0 Adapter. Windows 98se/ME/2000/XP Utility and Driver Installation 1. Insert the Wireless LAN USB 2. 0 Adapter Driver & Utility CD-ROM into computer's CD-ROM Drive and it will automatically run a setup menu and install the driver and the utility, for Win98se, please reboot the system to install the driver to the system properly. In some specific setting on Windows system, you may need to proceed the software manually, go to your Windows Start menu and choose Run, type "D:\Utility\Setup. exe" in the dialog box (D:\ will depend on where your CD-ROM drive is located) and click OK. If you need to install the driver manually, refer each Windows OS to the following CD-Rom directory path: D:\Drivers\<Windows OS>\SIS163U. INF. [. . . ] Fragment Threshold: Fragmentation Threshold is a way of transmitting the packets that will be fragmented. It is recommended to fragment the packet when the link quality is bad, it is to prevent the wasting time of resending a long packet that is lost. RTS/CTS Threshold: The RTS/CTS Threshold is a station initiates the process by sending a RTS frame, the other ends receives the RTS and responds with a CTS frame, the station must receive a CTS frame before sending the data frame. It is recommended limiting a long packet to prevent each station waiting too long to transmit a data. 11 Profile The Profile section allows you to set values for all parameters by selecting a previously defined profile. [. . . ]