User manual ENCORE ENRTR-514

[. . . ] ENRTR-514 Broadband Router User's Manual ENRTR-514 User's Manual FCC Warning This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limitations are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] WAN port is successfully connected to -5- ENRTR-514 User's Manual 100Mbps Off 100Mbps WAN port is successfully connected to 10Mbps STATUS On (Steady Green) Flashing LAN (1, 2, 3, 4) Reset On (Steady Green) Flashing On (Steady Green) Off System is hung. When push the reset button on rear panel When release the reset button on rear panel Back Panel Connectors Button/port Description Button/port Reset Description Reset configurations to default. Connect with AC power adapter. 1. 4 System Requirements Broadband connection and Cable/DSL modem Computers with wired network adapters CD-ROM Drive Operation System: Windows® 7/XP/2000, Windows Vista®, Mac® OS, UNIX®, Linux® Web Browser: Internet Explorer® 5. 0, Firefox® 2. 0 or Safari® 1. 4 or higher -6- ENRTR-514 User's Manual 2. PC Configuration User needs to configure TCP/IP network settings, Internet access configuration for each system within the ENRTR-514 Broadband Router's LAN network. By default, the Broadband Router acts as a DHCP server for server version of Windows, it automatically assigns IP address to each system when systems boot up. For all non-server versions of Windows, the default TCP/IP setting acts as a DHCP client. If you decide to use specific IP address, select "Use the following IP address". Make sure enter correct addresses in "IP Address" and "Subnet Mask" fields. You must set The Broadband Router's IP address as "Default Gateway". If the DNS Server fields are empty, select "Use the following DNS server addresses" and enter the DNS address is provided by your ISP, then click "OK". - 12 - ENRTR-514 User's Manual 3. Setup Broadband Router Configurations via Web Browser The ENRTR-514 4Ports Broadband Router comes with a web-based configuration utility. Users can access this configuration utility from any of client system within the Broadband Router's LAN. For best results, either use Microsoft Internet Explorer 6. 0 or later. Before you start configuring your Broadband Router, you have to get following information from your ISP: a) Has your ISP assigned you a static IP address, or they will assign one to you dynamically?If you are not sure of above questions, please contact your ISP immediately. 3. 1 Start your Web Browser To use the Web-Based Utility, you have to launch your Internet Browser (MS IE 6. 0 or later). Step1: Enter the Broadband Router default IP address http://192. 168. 0. 1 in the Address field then hit Enter key: Step2: Login dialog box will appear, enter admin as User Name and default password is admin, then click "OK" to login web-based utility. - 13 - ENRTR-514 User's Manual 3. 2 Quick Setup Quick Setup will help you setup the ENRTR-514 Broadband Router quickly. There are six types of WAN Connections: Dynamic IP Address, Static IP, PPPoE, PPTP, L2TP, and BigPond. When configure the Quick Setup wizard, you can setup Host Settings, such as Host name, Time Zone, and Daylight Saving as below. Click "Next" to continue. After specify the WAN connection type required by your ISP, please follow the next steps to configure DHCP and DNS settings to complete the wizard. Dynamic IP address: Obtain an IP address automatically from your service provider. Static IP: Use Static IP address to access Network, your ISP should provide a static IP address already. PPTP: PPP Tunneling Protocol can support multi-protocol Virtual Private Network (VPN) L2TP: Layer 2 Tunneling Protocol can support multi-protocol Virtual Private Network (VPN) BigPond: BigPond is an Australian internet service provider and is a subsidiary of Telstra. - 14 - ENRTR-514 User's Manual 3. 3 Administrator 3. 3. 1 Management Use this page to restrict management access based on a specific password. Passwords can contain from 4-12 alphanumeric characters, and are case sensitive. Idle Time-out - The amount of time of inactivity before the Broadband Router will automatically close the Administrator session. Remote Management - By default, management access is only available to users on your local network. [. . . ] Type: Select the Inbound port protocol type: "TCP", "UDP" or "Both". Comment: The description of this setting. - 28 - ENRTR-514 User's Manual 3. 6. 3 Port Mapping This functionality allows one or more public IP addresses to be shared by multiple internal users. Enter the Public IP address you wish to share into the Global IP field. Enter a range of internal IP that will share the global IP. Enabled: Enable the Port Mapping function. [. . . ]