User manual ENCORE ENLWI-SG

[. . . ] When nearby persons has to be kept to ensure RF exposure compliance, in order to comply with RF exposure limits established in the ANSI C95. 1 standards, the distance between the antennas and the user should not be less than 20 cm. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. [. . . ] Easy-to-use utilities are bundled with Wireless PCI Adapter for configuration, monitoring, and diagnosis purposes. Wireless PCI Adapter can wirelessly transmit and receive data, minimizing the need for wired connections, at a speed of up to fifty-four megabit per second. With Wireless PCI Adapter, you can locate your PC or station wherever you want without wires and cables. Wireless PCI Adapter provides users with an access to real-time information anywhere in their organization. The mobility provides productivity and service, which are not available under wired networks. The Wireless PCI Adapter configuration is easy to change from peer-to-peer networks, suitable for a small number of users, to full infrastructure networks of thousands of users that allow roaming around a broad area. Overview of this User's Guide Introduction. Helps you get started with the basic installation of the Wireless PCI Adapter. Lists the technical (general, physical and environmental) specifications of the Wireless PCI Adapter. 1 UNPACKING AND SETUP This chapter provides unpacking and setup information for the Wireless PCI Adapter. Unpacking Open the box of the Wireless PCI Adapter and carefully unpack it. The box should contain the following items: One 802. 11g Wireless PCI Adapter One Driver & Utility CD-ROM If any item is found missing or damaged, please contact your local reseller for replacement. Setup The setup of the Wireless PCI Adapter can be performed using the following steps: Visually inspect the PCI Adapter and make sure that it is fully plugged in to the PC's PCI slot. Make sure that there is a well environment that there is no much intrusion to have a better connection. 2 HARDWARE INSTALLATION LED Indicator LNK (Link) The LNK indicator indicates green when the Wireless PCI Adapter is connected to a network successfully. ACT (Activity) The ACT indicator blinks green continuously whiles the Wireless PCI Adapter is transmitting data. Check the installation 1. Shut down the computer, unplugs its power cord, and remove the chassis cover. Insert the contact edge of the Wireless PCI Adapter into the connector of any available PCI Bus Master Expansion slot. Press the card firmly into the connector such that the card's contacts are fully seated in the PCI slot connector. Install the bracket screw and secure the card to the computer chassis. The computer will automatically activate the newly installed driver and utility the Wireless PCI Adapter. 3 SOFTWARE INSTALLATION This section will lead you to install the driver and utility of the Wireless Cardbus Adapter. Windows 98se/ME/2000/XP Utility and Driver Installation 1. Insert the Wireless Cardbus Adapter Driver & Utility CD-ROM into computer's CD-ROM Drive and it will automatically run a setup menu and install the driver and the utility. In some specific setting on Windows system, you may need to proceed the software manually, go to your Windows Start menu and choose Run, type "D:\Utility\Setup. exe" in the dialog box (D:\ will depend on where your CD-ROM drive is located) and click OK. If you need to install the driver manually, refer each Windows OS to the following CD-Rom directory path: D:\Driver\<Windows OS>\net5211. inf. Note: (D:\ will depends on where the CD-ROM drive is located and <Windows OS> will depend on the Windows OS you are using). 3. The installation program will help you to setup the Wireless Cardbus utility. Be noted that the Windows XP have its own Wireless Utility; you can either use the utility of Windows XP or the provided utility. [. . . ] Click "Refresh" button to start scanning for available network again. Profile ­ User can create and manage the created profiles for Home, offices or public areas. By double-clicking on one of the created profile, the setting will adapt to the configuration such as SSID, channel, and WEP settings saved by that particular profile. Remove: To remove the selected the profile Properties: To view and change its settings of the profile. 9 Add: To add a profile. [. . . ]