User manual ENCORE ENL832-TX-RENT

[. . . ] This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. 1 CE-Mark Warning In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Document Version: 2. 0 All Trademarks and trade names are the properties of their respective owners. 2 1. Introduction Congratulations on the purchasing of your new 10/100 NWay Fast Ethernet PCI adapter. [. . . ] Then it is necessary to run the CMOS Setup utility, and manually assign a non-conflict Interrupt Number. 6 2. 3 Connect Fast Ethernet Category 5 UTP cable is required for Fast Ethernet operation. The maximum cable run between the adapter and the supporting hub is 300ft (100m). Make the network connection by plugging one end of the cable into the RJ-45 receptacle of the adapter, and the other end into one port in the hub. 2. 4 Connect 10Mbps Ethernet Category 3, Category 4, and Category 5 UTP cable, as well as EIA/TIA 568 100 ohm STP cable, all qualification under Ethernet cabling rules. The maximum cable length run between this adapter and the supporting hub is 300 ft. Make the network connection by plugging one end of the cable into the RJ-45 receptacle of this adapter, and the other end into the hub. 7 2. 5 Drivers and User's manual Diskette The [Divers and User's manual] diskette contains all the popular operating system drivers. Novell NetWare(client /server) Windows NT 3. 5, NT4. 0/2000/XP Windows 95/98/ME Microsoft Client (NDIS 2. 0 DOS/OS2) Windows For Workgroup 3. 11 . . . . and so on 2. 6 Software Installation Please refer to "Quick Installation Guide" 8 2. 7 Test Program This test program verifies configuration of the adapter and assists the isolation of any faults in operation. Test procedure are optional, and will only be useful in the unusual event that there is a fault, such as an interrupt number conflict among your computer's add on cards, If your installation provides normal operation, you do not need these test procedures. At your DOS prompt, type the following command: a:\rset8139. exe <Enter> The opening screen is displayed as following: View Current Configuration Set Up New Configuration Run Diagnostics Exit RSET8139 Choose <Set Up New Configuration> item allows you to set up the Network Speed, 10 or 100M, and Transmission Mode, Full or Half Duplex, and so on. Adapter test program includes: <Run EEPROM Test>, <Run Diagnostics on Board>, <Run Diagnostics on Network>, and <Run Power Management Test>. The <Power Management Test> is available for WOL adapter only. 9 After choosing the <Run Diagnostics on Board> item, the screen will display like, Node ID. . . . . . . . : 00 e0 7d c0 00 01 Network Speed. . : 100Mbps I/O Base . . . . . . : E000H Interrupt . . . . . : 11 Full-Duplex . . . : Disabled Pass Count Count A. Cable Connection <Cable Connection> test reminds you that the connection link might be fail, either the cable is not connected or the cable link fails. For the <Run Diagnostics on Network> test, it is necessary to connect your computer with its supporting hub or another computer. This test cannot be completed except two computers on the LAN for sending or receiving the test packets between computers. 10 Fail 11 For the <Run Diagnostics On Network> test Ethernet Address 00E07DC00002 Target Machine Ethernet Address 00E07DC00001 Master Machine Netwok Master Machine: Master machine sends magic packet or Wake up frame through the network. Target Machine: Target machine is notified whenever a qualified wakeup packet is received. 12 Quick Installation Guide Please take the following steps for driver installation. After Microsoft Windows reboot, the PCI Ethernet Controller will be found. Insert the "Driver and Utilities" diskette into diskette driver and press <Enter>. For Windows 98, Key in a:\w98_2000 path to install driver for the adapter 9. For Windows ME, Key in a:\winme path to install driver for the adapter 10. [. . . ] Select "Network Connection" folder then click "Local Area Connection" and "Properties". From the "Driver" item then choose "Update Driver" 9. Choose "Install from a list or specific location (Advanced)" and click "Next". Select "Don't search, I will choose the driver to install" then click "Next". [. . . ]