User manual ENCORE ENHWI-N

[. . . ] ENHWI-N ENCORE 802. 11n Wireless Router User Manual FCC Certifications Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Bandwidth QoS Settings Items Enable this Rule Type LAN IP Address Priority Bandwidth Comment Action Information Mark to enable the configuration, and clear to disable. After configuring the above settings, click Add to add a new list in the following MAC Access Control List. The Change button can be used to change the configuration. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. Bandwidth QoS Settings Lists the Bandwidth QoS Settings you have added before. Click on the list to change configuration, or the Delete button to delete the list. 16 Wireless Settings Basic Settings You can set up the configuration of your Wireless and monitor the Wireless Clients associate with your AP. Information Mark the checkbox to enable Wireless interface or uncheck to disable. To select a band for this device to match 802. 11g/b/n Wireless Mode mixed, 802. 11g/b mixed, 802. 11b, 802. 11g, or 802. 11n. Country Wireless Channel Select a channel for the wireless network of this device. Service set identifier for the name of the wireless SSID network. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. Items Enable Wireless 17 Advanced Settings You can set advanced wireless LAN parameters of this router. We recommend not changing these parameters unless you know what changes will be there on this router. 18 General Wireless Advance Settings Information Mark to disable SSID from broadcasting. As default, this device broadcasts its SSID to allow every wireless station located within the coverage of this wireless router to discover this wireless router easily. The period of time a beacon is broadcasted (default Beacon Period 100ms). The beacon of a Delivery Traffic Indication Message DTIM Period is broadcasted (default 1 beacon). If the packet size is smaller than the Request To RTS Threshold Send threshold, the wireless router will not send this packet by using the RTS/CTS mechanism (default 2347 bytes). Fragment Threshold Specifies the maximum size of packet during the data transition. A higher value brings a better performance (default 2346 bytes) Select the Transmission Power of very weak, weak, Tx Power medium, and strong according to your demand. Select "Auto" to turns it on or off automatically, select "Always On" to support protection or select "Always Off" to disable this function. Support WMM * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. Items Hide SSID 802. 11n Wireless advance Settings Information Select the mixed or green field mode as the Hyper Throughput operation mode. Select the 40MHz or 20MHz as the channel HT Channel Bandwidth bandwidth. HT Guard Interval Enable HT TX Aggregate Mark to enable Hyper Throughput TX Aggregate MAC Service Data Unit, and clear to disable. MSDU * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. Items HT Operation Mode 19 Security Settings The Security function protects your wireless network from invasion. If you select none, any data will be transmitted without encryption and any station can access the router. 20 WEP Configuration Items Authentication Default Key ID WEP Key 1, 2, 3 and 4 Information Open: Wireless AP can associate with this wireless router without WEP encryption. Shared Key: Wireless AP can associate with this wireless router only with WEP encryption. Select to use the WEP key value of 1, 2, 3 or 4 as in the following settings. [. . . ] Click on the list to change configuration, or the Delete button to delete the list. 38 Services Settings DDNS Settings DDNS (Dynamic Domain Name Server) service allows users to connect to this device via a fixed and easy-to­remember hostname. Items Enable DDNS Service Provider Domain Name User Name/Email Password/Key Confirmed Password Information Mark to enable the configuration, and clear to disable. For DynDNS users, please fill in your user name; for No-IP and TZO users, please fill in your email address (default USER). Retype the password to confirm. * Please click on the Save Settings button or the Reset Settings button on the above table to save/reset the configurations. 39 UPnP Settings The UPnP (Universal Plug and Play) service allows devices to connect seamlessly and to simplify the implementation of networks in the home (data sharing, communications, and entertainment) and corporate environments. Mark or clear the checkbox to enable or disable UPnP IGD, and then click Save Settings to enact your settings. 40 System Log Settings The System Log Settings page shows the information of the current activities on the router. Items System Log Information Mark to enable the configuration, and clear to disable. [. . . ]