User manual ENCORE ENHWI-G2

[. . . ] ENHWI-G2 802. 11g Wireless Broadband Router Users Guide Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Choose this option and enter the required information. Figure 29 27 Step 5: Set Wireless LAN connection Click "Enable" to enable wireless LAN. If user enables the wireless LAN, type the SSID in the text box and select a communications channel. The SSID and channel must be the same as wireless devices attempting communication to the router. Figure 30 Step 6: Restart The Setup wizard is now completed. The new settings will be effective after the Wireless router restarted. If user does not want to make any changes, please click "Exit" to quit without any changes. 28 Figure 31 WAN Setting This function enables users to set up the WLAN Router WAN connection, specify the IP address for the WAN, add DNS numbers, and enter the MAC address. Connection Type: Select the connection type, either DHCP client, Fixed IP or PPPoE, PPTP, L2TP or BigPond from the drop-down list. 29 DHCP Client or Fixed IP If user has enabled DHCP server, choose "Obtain IP automatically (DHCP client)" to have the router assign IP addresses automatically. Figure 32 WAN IP Address: Select whether user wants to specify an IP address manually, or want DHCP to obtain an IP address automatically. When Specify IP is selected, type the IP address, subnet mask, and default gateway in the text boxes. IP Address: For the Specify mode, enter the specific IP address that provided by your ISP. Subnet Mask: For the Specify mode, enter the specific subnet mask that provided by your ISP. Gateway: For the Specify mode, enter the specific gateway IP address that provided by your ISP. DNS1 and DNS2: Manually specifies the DNS server IP address, these fields will only be accessible if "Specify IP" is selected, otherwise these fields are grayed-out. To obtain IP address automatically from the DHCP server select "Obtain IP Automatically", the DHCP server will provide DNS server IP automatically as well. Clone MAC Address: If your ISP requires you to enter a specific MAC address, please enter it in. The Clone MAC Address button is used to copy the MAC address of your Ethernet adapter to the Router. 30 PPPoE with Obtain IP Automatically If connected to the Internet using a PPPoE (Dial-up xDSL) Modem, the ISP will provide a Password and User Name, and then the ISP uses PPPoE. Choose this option and enter the required information. Figure 33 31 PPPoE with Specify IP If connected to the Internet using a PPPoE (Dial-up xDSL) Modem, the ISP will provide a Password, User Name and a Specify IP Address, choose this option and enter the required information. Figure 34 32 PPTP/L2TP with Obtain IP Automatically If connected to the Internet using a PPTP/L2TP (Dial-up xDSL) connection, enter the your Server IP, PPTP/L2TP Account and PPTP/L2TP Password, if your ISP has provided you with a DNS IP address, enter it in the DNS field, otherwise, leave it zero. Figure 35 PPTP Figure 36 L2TP PPTP/L2TP with Specify IP If connected to the Internet using a PPTP/L2TP (Dial-up xDSL) connection, enter the your IP Address, Subnet Mask, Gateway IP address, DNS IP address, Server IP address, PPTP Account and PPTP Password. 33 Figure 37 PPTP Figure 38 L2TP 34 BigPond Cable If your ISP is Big Pond Cable, the ISP will provide a User Name, Password, Authentication Server and Login Server IP (Optional). Choose this option and enter the required information. Dynamic DNS: This synchronizes the DDNS server with your current Public IP address when you are online. First, you need to register your preferred DNS with the DDNS provider. Then, please selected one of DDNS server than fill the related information in the below fields: Host Name, User Name and Password. 35 Figure 39 Wireless setting This section enables user to set wireless communications parameters for the router's wireless LAN feature. Basic This page allow user to enable and disable the wireless LAN function, create a SSID, and select the channel for wireless communications. 36 Figure 40 Wireless: Enables or disables the wireless LAN function of the wireless LAN Router. The SSID of any wireless device must match the SSID typed here in order for the wireless device to access the LAN and WAN via the router. Extended Range Mode: Enable and disable the wireless Extended Range enhancement. SSID Broadcast: While SSID Broadcast is enabled, all wireless clients will be able to view the WLAN Router's SSID. [. . . ] Click "DHCP Release" to release all IP addresses assigned to client stations connected to the WAN via the WLAN Router. Click "DHCP Renew" to reassign IP addresses to client stations connected to the WAN. 59 Log This function enables users to view a running log of Router system statistics, events, and activities. Older entries are overwritten by new entries. Figure 65 The Log screen commands are as follows: Click "First Page" to view the first page of the log Click "Last Page" to view the final page of the log Click "Previous Page" to view the page just before the current page Click "Next Page" to view the page just after the current page Click "Clear Log" to delete the contents of the log and begin a new log Click "Refresh" to renew log statistics 60 Log Setting This function enables users to set Router Log parameters. Figure 66 SMTP Server: Type-in your SMTP server address here. SMTP Authentication: Select Enabled if the SMTP server need authentication, fill in your account username and password in SMTP Account field and SMTP Password field. [. . . ]