User manual ENCORE ENDSL-A2 PLUS WIGX2

[. . . ] ENDSL-A2+WIGX2 ADSL2+ Modem With Four Port Ethernet and 802. 11g Wireless Router User's Manual August 2007 FCC Warning ENDSL-A2+WIGX2 has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] The only difference 6. 2. 3 DHCP Server The DHCP Server gives out IP addresses when a device is booting up and request an IP to be logged on to the network. It must be set as a DHCP client to obtain the IP address automatically. The DHCP address pool contains the range of the IP address that will automatically be assigned to the client on the network. 45 LABEL Starting IP Address DESCRIPTION Enter the starting IP address you wish to use as the DHCP server's IP assignment. IP Pool Count Lease Time DNS Relay Primary DNS Server Enter the maximum user pool size you wish to allow. For user discovered DNS only. Secondary DNS Server Enter the secondary DNS server IP address you wish to use. For user discovered DNS only. 6. 2. 4 DHCP Relay A DHCP relay is a computer that forwards DHCP data between computers that request IP addresses and the DHCP server that assigns the addresses. Each of the device's interfaces can be configured as a DHCP relay. If it is enable, the DHCP requests from local PCs will forward to the DHCP server runs on WAN side. To have this function working properly, please run on router mode only, disable the DHCP server on the LAN port, and make sure the routing table has the correct routing entry. DHCP Server IP for relay agent: The DHCP server IP Address runs on WAN side. 46 6. 2. 5 DNS Relay The DNS Configuration allows the user to set the configuration of DNS. DNS Rely Selection: If user wants to disable this feature, he just needs to set both Primary & Secondary DNS to 0. 0. 0. 0. Using DNS relay, users can setup DNS server IP to 192. 168. 1. 1 on their computer. If not, device will perform as NO DNS relay. If you don't want to use the DNS Relay option, set the DNS relay to "Use User Discovered DNS Server Only" and set both Primary and Secondary DNS Servers to "0. 0. 0. 0". 47 6. 3 Wireless 6. 3. 1 Access Point Settings Beacon Interval: The Beacon Interval value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Router to synchronize the wireless network. RTS/CTS Threshold: The RTS (Request To Send) threshold (number of bytes) for enabling RTS/CTS handshake. Data with its frame size larger than this value will perform the RTS/CTS handshake. Set this attribute to be larger than the maximum MSDU (MAC Service Data Unit) size TURNS OFF the RTS/CTS handshake. Fragment Threshold: The threshold (number of bytes) for the fragmentation boundary for directed messages. DTIM: This value is between 1 and 255, indicates the interval of the Delivery Traffic Indication Message (DTIM). 6. 3. 2 Multiple SSIDs Settings SSID: The SSID is a unique name to identify the ADSL Router in the Wireless LAN. Wireless Clients associating to the ADSL Router must have the same SSID. Broadcast SSID: Select No to hide the SSID such that a station can not obtain the SSID through passive scanning. Select Yes to make the SSID visible so a station can obtain in the SSID through Passive scanning. Channel ID: The range of radio frequencies used by IEEE 802. 11b/g wireless devices us called a channel. [Authentication Type] WEP (Wired Equivalent Privacy) encrypts data frames before transmitting over the wireless network. Select Disable to allow all wireless computers to communicate with the access points without any data encryption. [. . . ] 4 For WAN access, you must configure remote management to allow server access from the WAN (or all). 5 Your computer's and the router's IP addresses must be on the same subnet for LAN access. 6 7 If you changed the router's LAN IP address, then enter the new one as the URL. Remove any filters in LAN or WAN that block web service. The web Interface does not display properly. STEPS 1 2 CORRECTIVE ACTION Make sure you are using Internet Explorer 5. 0 and later versions. [. . . ]