User manual EMERSON HD1300WC0C

[. . . ] No employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson Electric. The customer shall be responsible for all costs incurred in the removal or reinstallation and shipping of the product for repairs. Within the limitations of this warranty, inoperative units should be returned, freight prepaid to the nearest Emerson authorized service centre, or the Emerson Electric Co. Service Centre, and we will repair or replace, at our option, at no charge to you with return freight paid by Emerson. [. . . ] Step 2 The humidifier should be positioned with the back (cord exit side), at least 2 inches away from the wall. Air needs to enter through louvers in the back of the cabinet in order for the humidifier to operate at peak efficiency. At Least 2" From Wall Water Fill WARNING: To reduce the risk of shock, always unplug humidifier before filling, cleaning, or servicing. WARNING: To reduce the risk of fire or shock hazard, do not pour or spill water into control or motor area. If controls get wet, let them dry completely and have unit checked by authorized service personnel before plugging in. This humidifier is designed to be used with the two water bottles that are located under the pivoting lid. Pivoting Lid Removed for Clarity Fan Assembly Water Bottles Cabinet 5 Front of Humidifier HD1300 3 US manual 11/14/00 1:40 PM Page 6 Water Fill (continued) Open the pivoting lid of the humidifier. Remove the water bottles, by lifting them straight up and out of the cabinet. Position them in the correct location so the humidifier can function properly. Each "E-Z-Fill Side-Cap" must be facing the rear of the unit Each water bottle is designed with an "E-ZFill Side-Cap" that is easily removable. Remove the "E-Z-Fill Side-Cap" on the side of the water bottle by twisting counterclockwise. Place the opening of the water bottle under a water faucet (the bottle should fit under a four-inch clearance faucet). Fill with recommended mixture of cold water and if necessary Emerson WT-BC Bacteriostat only. The higher the air flow speed, the more water is evaporated and released into the air. MIN speed is the quietest and is provided for conditions that may not require as high an evaporation rate. MIN MAX MAX OFF AIR FLOW MIN Fill Light When the unit has a small amount of water left in it, the fill light will come on and the unit will automatically shut off. FILL FAN 7 HD1300 3 US manual 11/14/00 1:40 PM Page 8 Using Your Humidifier Step 1 Be sure unit is full of water and plugged in. This will allow both fans to operate if the humidistat senses humidity is needed. Step 4 Set Humidity Control to medium position (half way between MIN and MAX. ) NOTE: Humidifier should operate with humidity control on the recommended medium setting. To test the unit under this condition, turn Humidity Control all the way to MAX and unit should begin to operate. After the unit has been tested, set Humidity Control to medium or desired level. Allow 24 hours for humidifier to adjust. Humidity Rel. Step 5 If humidifier stops running and the Fill Light is not illuminated, the humidity level is at the normal requirements for that setting or it is adjusting to the home conditions. The figure below shows approximate relative humidity percentages which correspond to the various settings of the Humidity Control. When Outdoor Recommended Indoor Temperature is: Relative Humidity is: -10°F 0°F 10°F 20°F & above Rel. Humidity 20% 25% 30% 35% If humidity level in home is sufficient, the humidifier will only operate with Humidity Control set on maximum. IMPORTANT: Water damage may result if condensation starts to form on windows or walls. Clean internal parts of humidifier per the "Cleaning Your Humidifier" section of your owner's manual. Pivoting Lid Fan Assembly Spring Tabs Filter Housing 9 HD1300 3 US manual 11/14/00 1:40 PM Page 10 Replacement and Care of Filters (continued) c. [. . . ] The cabinet consists of the lower areas of the humidifier where the filters are during normal operation time. Proceed to "Bi-Weekly Maintenance" or "End of Season Maintenance" then continue as described below. Remove old filters and dispose of properly as described on page 9 and 10. Step 3 Install new filters (use Emerson HDC-12 Replacement Filters) into the location where the old filters were positioned. [. . . ]