User manual EMERSON EWD2203M

[. . . ] OWNER'S MANUAL EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS OF EMERSON RADIO CORP. , PARSIPPANY, NEW JERSEY, U. S. A. DVD PLAYER with VIDEO CASSETTE RECORDER EWD2203M ReWritable Recordable OPEN/CLOSE POWER CH-UP STOP REV PLAY FWD DVD STOP/EJECT OUTPUT VCR TIMER REC REC REW FF PLAY DISC IN VIDEO AUDIO CH-DOWN PLAY SERVICING Should your DVD/VCR COMBINATION UNIT become inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power plug, and take the unit to our Authorized Service Center. Please read before using this equipment. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] Repeat only if there is a power failure or if the VCR is unplugged for more than 30 seconds. (In these cases, the programmed channels are erased. ) ¡You must follow the steps below before attempting to play or record a video tape. If you want to play or record a video tape BEFORE programming the tuner, you can cancel it by pressing CLEAR/C. RESET. 5 Begin channel preset by pressing B once. The tuner scans and memorizes all active channels in your area. ¡The VCR distinguishes between CH 01 AUTO SET UP standard TV channels and cable channels. 6 After scanning, the tuner stops on the lowest memorized channel. ¡If "AUTO SET UP" appears on the TV screen again, check the cable connections. Press B once again and the VCR will begin preset again. TO SELECT A DESIRED CHANNEL You can select the desired channel by using CHANNEL (UP/DOWN) or by directly pressing Number on the remote control. Note for using the Number: ¡When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number. (For example: 117, press 1, 1, 7) ¡You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on). 1 You need to connect the antenna or cable to the VCR first. Then, connect the DVD /VCR power plug to a standard AC outlet. TO PRESET THE CHANNELS AGAIN 1 Press MENU until the main menu appears. (If you have already set the clock, you only have to press it once. If not, you have to press it twice). 2 Turn on the TV and set the TV to channel 3. ¡If noise appears, change the RF output channel of the VCR to channel 4 by pressing PLAY for 3 seconds during playback. (See "RF OUTPUT CHANNEL" on page 13 for the detail. ) 2 Select "CHANNEL SET UP" by pressing K or L. the POWER light will come on. 3 Select "TV" or "CATV" by pressing K or L. Then, press B. ¡After scanning, the tuner stops on the lowest memo- 4 Select the On Screen Language ("ENGLISH", "FRANCAIS" or "ESPAÑOL") by pressing K or L. Then, press B. rized channel. ­ 16 ­ EN 1L25 TO ADD/DELETE CHANNELS When scanning, some channels may be skipped due to a weak signal. In such cases, you can add the channels to the VCR memory manually. CLOCK SET UP VCR 1 Select main menu by pressing MENU. 1 Press MENU until the main menu appears. (If you have already - MENU TIMER PROGRAMMING set the clock, you only have AUTO REPEAT UP [OFF] CHANNEL SET CLOCK SET LANGUAGE SELECT to press it once. If not you AUDIO OUT [ON] TV STEREO SAP have to press it twice). ¡If the clock is not set, the CLOCK SET menu appears first. In this case, follow step [3]. 2 Select "CLOCK SET" by pressing K or L. Then, press B. 2 Select "CHANNEL SET UP" by pressing K or L. Then, press B. 3 Set the clock. 1) Set the month 3 Select "MANUAL SET UP" by pressing K or L. Then, press B. 2) Set the day 4 Enter the desired channel number by pressing K or L. 5 Add or Delete it from memory by pressing B or s so that "ADD" or "DELETE" flashes on the TV screen accordingly. Press K or L repeatedly. Then, press B. 3) Set the year 6 Exit the Preset mode by pressing CLEAR/C. RESET. Press K or L repeatedly. The day of the week will appear automatically. 4) Set the hour Press K or L repeatedly. Then, press B. TO CHANGE THE ON-SCREEN LANGUAGE VCR 1 Press MENU twice to call up the main menu. (If you have already set the clock, you only have to press it once). 5) Set the minute Press K or L repeatedly. [. . . ] Video or color fades in and out · You cannot copy a copyrighted video tape. · There are some cases where pictures may be slightly distorted, which are not a sign of a malfunction. · Although pictures may stop for a moment, this is not a malfunction. Audio or subtitle language · The selected language is not available for audio or subtitles on the DVD. [. . . ]