User manual EMERSON ET-13P2

[. . . ] INSTRUCTION MANUAL Color Television ET ET 13P2 19P2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION The AC power cord provided with this product is polarized (one blade wider than the other). To provide power to the TV, insert the AC plug into a standard 120V 60Hz polarized outlet. NOTE Never connect the plug to an electrical source other than one providing 120V 60Hz power. [. . . ] Follow these steps to program your TV's memory: 1 With the TV on, press the MENU button twice, then "Set-Up" menu will appear. 2 Use the w CHv buttons to select "Reception", then use the CVOLB button to select `Air' or `Cable'. If you connected an antenna to your TV, select `Air'; If you connected a cable system, select `Cable'. 3 Use the w CHv buttons to select "Memorize Channels", then use the CVOLB button to enter the "Memorize Channels" process. You will not need to re-program the memory unless you change the type of cable or antenna connected to your TV. 1 2 Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels 3-1 Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Select Adjust Next Select Adjust Next Select Adjust Next 3-2 Memorize Channels Air 11 Memorizing all air channels. Please stand by. 4 5 Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Press MENU to cancel and returu to Set-up menu. Select Adjust Next 10 Chapter 3: Operating Your TV Changing Channels You can change channels in three ways: 1 2 3 1 The w CHv buttons will take you through all memorized channels, one by one. The wCHv buttons will not access channels that have not been programmed into the TV's memory. For more information about programming channels into memory, see the section "Programming your TV's Channel Memory" on the previous page. The number buttons (0-9) will take you to any channel, even if it has not been memorized. To change to a channel, enter its number; the TV will tune to the new channel when you enter the second digit of the channel. The PREVIOUS button will take you instantly to the last channel you were watching. 2 3 Changing the Volume 1 2 1 2 To change the volume of the TV set, use the CVOLB buttons on the remote or on the front panel. To return the volume to its previous level, press MUTE again. Chapter 3: Operating Your TV 11 Changing the TV's Channel Memory Your TV's memory determines the channels that are available using the w CHv buttons. If a channel is removed from memory, you can tune to it with the number buttons, but you cannot tune to it with the w CHv buttons. If there are just one channel memorized, then the Add/Delete Channels function will search the whole channels. But if there are two or more channel memorized, then the Add/Delete Channels function will search the memorized channels only. Adding/Deleting a channel to memory 1 Use the number buttons to tune to the channel. 2 Press the MENU button twice, then "Set-Up" menu will display. 3 Use the w CHv buttons to select "Add/Delete Channels", then use the CVOLB button to enter the "Add/Delete Channels" process. 4 If the channel is not in memory, then use the CVOLB button to add the channel from memory. 5 If the channel is in memory, then use the CVOLB button to delete the channel from memory. 6 If you are going to delete other channel, then press the w CHv buttons until desired channel is selected. 7 Wait 10 seconds, or press the MENU button four times to exit. 1 2 3 11 Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Set-Up Language : English Reception : Air Memorize Channels Add/Delete Channels Select Adjust Next Select Adjust Next 4 5 6 Add/Delete Channels Air 11 This channel is not in memory. [. . . ] If user have a cable box with AC outlet, then user can connect the TV power cord to the AC outlet and control the TV without TV remote control. This function is rarely used for home use, so special care is needed while using. 1 With the TV turned on, press the MENU button until `Special" menu will be displayed. 3 Use the CVOLB buttons to select "On" or "Off". 1 2 3 Special Closed Caption : C 1 CC on Mute : C 1 Power Restore : OFF Auto Tint : OFF Special Closed Caption : C 1 OC on Mute : C 1 Power Restore : OFF Auto Tint : OFF Special Closed Caption : C 1 OC on Mute : OFF Power Restore : On Auto Tint : OFF Select Adjust Exit Select Adjust Exit Select Adjust Exit Chapter 5 : Additional Features 19 Auto Tint(option) This is function for fresh tone compensation. [. . . ]